Industrial Flooring

Primers

Monneli Primer Poxy (IF)

Penetrating Solvent-Free Epoxy Primer for Concrete Floors

Uses
Commercial and residential car parking
Workshops
Warehousing and storage facilities
Chemical and pharmaceutical factories
Food factories and slaughterhouses
Schools and office buildings
back to Industrial Flooring
Technical Information
Product Description

PRIMER POXY (IF) is a solvent free primer based on formulated epoxy resin and curing agents specially selected for their ability to be applied and cured in warm temperatures, on dry or damp concrete.

Once the PRIMER POXY (IF) hardens, the concrete surface becomes much harder allowing application on weaker concrete possible.

Packaging, Coverage / Consumption

PRIMER POXY (IF) is supplied as a pre-measured kit depending on the customer’s requirements. Our standard packaging is 4 Liter and 15 Liter Kit.

 

Components

 

PRIMER POXY (IF) contains resin (Component A) and hardener (Component B):

  • PRIMER POXY (IF) resin (Component A) is a low viscosity resin that is clear containing no fillers or pigments.
  • PRIMER POXY (IF) hardener (Component B) is a low viscosity hardener which, after mixing with the resin, can be applied at 95% humidity and on damp surfaces.
Shelf Life & Storage

Keep in tightly closed containers and in sheltered and dry place with a temperature between 5°C and 35°C. In these conditions it maintains its characteristics unchanged for 12 months.

Technical Properties
Solid Content

100%

Recommended DFT / coat

50-100 microns

Kit Size

4 Liters

Theoretical Coverage

40-80 m2 / 4 liter kit

Kit Size

15 Liters

Theoretical Coverage

150 - 300 m2/15 liter kit

Pot Life at 18°C

50 minutes

Pot Life at 30°C

30 minutes

Thin Film (75μm) Dry Time at 25°C

5-6 hours

Mixing Ratio HARDENER : BASE (by weight)

1.0 : 1.67

Mixed Density at 20°C

1.10 kg/L

Max Recoat/Topcoat Time at 25°C

24 hours

Application Maximum Relative Humidity

95 %

Bond Strength to Concrete (ASTM D4541)

> 2.0 N / mm2

Taber Abrasion (ASTM D4060 CS17 Wheels)

55 mg loss/1000cycles

Water Absorption (ASTM D413 ) (maximum)

0.001%

Porosity with no sealer NACE Sand TM-01-74

0

Hardness Shore D

80

Application Information
Instructions for use

Application Thickness

A thickness of 50-100μm per coat is recommended. In case the concrete is very porous, you can apply a second coat of PRIMER POXY (IF).

Application

Items Needed

  • Multi-speed drill fitted with a mixing paddle.
  • Good quality medium haired non-shedding roller, suitable for epoxy application. Ensure that all loose hairs on the roller have been removed before use.
  • 7” flat squeegee.
  • Clean bucket, 2” brush and SOLVENTE 10 to clean the equipment

Method

Using a drill and a paddle at low speed, stir the resin (Component A) for 1 minute.

Slowly add the hardener (Component B) and increase mixing speed. Mix for 3-4 minutes, ensuring proper mixing between the resin and the hardener components until a completely homogeneous mixture is obtained.

The best method to apply the mixed product is by pouring it over the prepared surface. Then using a flat squeegee spread the material uniformly over the surface and back roll it maintaining the recommended thickness. Using just the roller is also possible.

In case the surface is very absorbent, apply a second coat of primer within the allowed recoating time.

Cleaning

Clean equipment with SOLVENTE 10. In case of spillage, use fine silica or cement to absorb the spill and dispose of according to local regulations.

Surface Preparation

The concrete must be at least 28 days old. The concrete must be free from loose matter, oil and dirt before starting surface preparation.

The best method to prepare the surface is dry grinding using a specialized planetary grinder. Before grinding, the surface must be free from any degreasing or cleaning chemicals which may have been used. At the end of grinding, the surface should be flat.

Surface irregularities and blow holes shall be repaired with EPOFINISH IF.

When the filler is hardened, grinding and leveling of the patched area is recommended to ensure a good finish.

Ensure dust is removed from the surface using an industrial vacuum.

Metal surface must be perfectly cleaned up to white metal by sand blasting. Application of PRIMER POXY IF should be done immediately before flash rusting occurs.

Additional Information
Health & Safety

Study the MSDS of the product before use or storage.

PRIMER POXY (IF) is not regulated per the “Directive 67/548/EEC EU Dangerous Materials List” so no special labeling is needed

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.07Mb)
OTHER PRODUCTS
More Products from this section
Monneli Primer Poxy

Solvent Based Epoxy Primer

Monneli Primer Poxy (FC)

Fast Cure Solvent-Free Epoxy Primer for Concrete Floors

Monneli Primer Poxy FF

Solvent Free High Performance Epoxy Primer

Monneli Primer Poxy PU

Solvent Free High Performance Epoxy Primer

Monneli Primer Poxy WB

Water Based Epoxy Primer

view more
RANDOM PRODUCT
Monneli Betocem Fibre

Fibre Reinforced Shrinkage Controlled Mortar for Concrete Repair

Uses
Repairs for edges of beams and pillars
Risers of balconies & terraces
Tunnels
Degraded concrete castings
Reconstruction of concrete structural elements - filling honeycombs in reinforced concrete, rigid joints filling, etc.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map