Tile Adhesives

Acrylic Based Adhesive

Monneli Neofil P8

Ready-Mixed Elastic Tile Adhesive Paste

Uses
NEOFIL P8 is used for interior laying of woods, vinyls, tiles and ceramics, mosaics of every type, natural stones, on cement plasters, prefabricated panels, reinforced concrete, asbestos cement and on gypsum plasters, gypsum panels, plasterboard, etc., without the necessary of using PRIMER A 16.
Thanks to its elasticity, NEOFIL P 8 is particularly suitable for fixing tiles on walls or floors affected by strong movements.
It is used for the gluing of insulating materials such as polystyrene, expanded polyurethane, expanded cement elements, etc. on porous supports.
back to Tile Adhesives
Technical Information
Product Description

NEOFIL P8 is an acrylic modified paste adhesive ready to use product composed of synthetic resins, fillers  and special additives. NEOFIL P8 is water based and has a form of viscous, but easily applicable paste.

Advantages
  • Good elasticity
  • Water resistant
  • Eco-friendly
  • Good open time
  • Formulated to suit Middle East conditions
Compiliance Standard
  • EN 12004 – D1TE
  • ANSI A 136.1 – 1999
  • EN 1346, EN 1324
Packaging, Coverage / Consumption

Packaging:

NEOFIL P8 is supplied in 20kg plastic containers.

 

Consumption: 

From 3.0 - 4.0kg per m² using notched trowel on smooth surface. Consumption will vary according to type of tiles and to support condition.

Shelf Life & Storage

Storage:

12 months in well closed original containers if kept in a dry covered store.

Technical Properties
PROPERTIES RESULTS
Appearance Dense paste
Color  White
Density at 25°C  1.50 kg/L 
VOC <5.0 
Solid content 85%
Viscosity  800,000 cps
Open time 45 minutes
Wall grouting After 10 hours
Floor grouting After 24 hours
Ready for use  After 7-14 days
Shear strength (EN 12004) >1.8 N/mm²
Harmfulness L. 88/379 EEC No
All values are subject to 5-10 % tolerance  
Application Information
Instructions for use

Surface preparation

All the supports where NEOFIL P8 will be applied must be perfectly plane, solid, compact, free form dust, grease and any other material that can harm a perfect adhesion.

Mixing

Stir NEOFIL P 8 thoroughly before use.

Application

Apply NEOFIL P8 with a toothed spatula, spreading first pass with the spatula from the smooth part and then the second pass with the toothed part.
Place the tile on the adhesive bed applying sufficient pressure.  To ensure full adhesion, fix the tile firmly with a slight twisting movement. In case of large size tiles, spread adhesive onto the backside of the tile (back-buttering) as well and then place the tile in to the adhesive bed. Apply enough material that can be tiled during the adhesive’s open wet time. Spreading large areas may result in drying the adhesive before tiles can be fixed causing poor adhesion.

Finishing

Remove excess adhesive with damp cloth before the material has set. Joint grouting between tiles may be commenced 10hours after tiles has been laid on the walls and 24 hours after tiles are laid on the floors.

Cleaning

Clean used tools with warm water after application is completed and before product dries.

Recommendations

  • Despite the fact that NEOFIL P8 has a discreet water resistance, it cannot be applied on screed or floors in presence of continuous humidity.
  • Don’t use NEOFIL P8 for gluing of non-porous materials on non-porous supports, for instance, tiles over already existing ceramic floors
  • Do not apply NEOFIL P8 in rainy weather, high winds and sand storms
  • Do not apply under direct sun
  • Keep equipment cool and use cold water
Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Neofil M10

Ready to Use Acrylic Adhesive for Floorings

RANDOM PRODUCT
Monneli Epofinish C

Fairing Coat Solvent Free Epoxy Mortar

Uses
EPOFINISH C is designed to provide repairs to surfaces in different situations, such as:
Crack repairs in structural components, like bridges, industrial structures, columns, beams, foundations, walls and floors slabs
Filling pinholes prior to over coating
General re-profiling over large areas
Dowel bars anchoring
Bolt pocket, filling
Used as adhesive to fix slip brick to concrete
Repair surface defects on steel bridges bearings
Used as bedding mortar for bridge beams or steel bridges bearing
Used as mortar bedding in manhole chambers
General re-profiling over large areas
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map