Mortar Specialties

Cement Based Mortar

Monneli Dashbond

Spatter Dash Bond Coating

Uses
DASHBOND can be used as:
Rough scratch coat before applying cement plaster
Base coat on precast, cement block and conventional buildings
back to Mortar Specialties
Technical Information
Product Description

A cement based premixed product for application on smooth concrete walls and ceiling (not contain micro-silica) to work as a rough scratch coat before applying the cement plaster.
Made to be applied directly to smooth concrete surfaces without the need to roughen the surface by hacking it.
Suitable as a base coat on precast, cement block, and conventional buildings.

Advantages
  • High quality premixed spatter dash bond coat
  • Water resistant
  • For exterior and interior use
  • Excellent workability and easy to use
  • High strength and bonding properties
Compiliance Standard
  • ASTM C579
  • ASTM C580
  • EN 1015
Packaging, Coverage / Consumption

Packaging:

DASHBOND is supplied in 50kg bags.

 

Consumption:

Up to 20m² per 50 Kg/1.7mm depending on the method of application and surface condition.

 

Shelf Life & Storage
  • ASTM C579
  • ASTM C580
  • EN 1015
Colors
Grey
Technical Properties
PROPERTIES

RESULTS

Appearance

Powder

Color

Grey

Density

1.8 kg/L

VOC

2.1g/L

Compressive strength at 28 days (EN 1015)

25 N / mm²

Flexural strength at 28 days (EN 1015)

4.5 N/mm2

Chloride content

Nil

Inflammability

No

Toxicity

Non-toxic

All values are subject to 5-10 % tolerance

Application Information
Instructions for use

Composition

DASHBOND consists of Portland cement, special high strength hydraulic binders, aggregate and special chemical additives to achieve a high strength adhesion with water resistance and crack free coat.

Surface preparation

Remove dust, loose particles, grease and traces of foreign materials which may affect the adhesion. Remove all traces of curing compound films and shuttering oil. Do not use paint remover or solvent to clean the surface. Moisten the concrete with clean water before applying DASHBOND. Running water on the surface should be allowed to drain prior to application.

Mixing

Add the content of DAHSBOND bag into a container of 11 Liters of clean water. Mix until a uniform, lump free consisting mix is achieved. For mixing process, a slow speed drill (200 to 300 rpm) fitted with a suitable paddle is recommended. Let the composition stands for nearly 5 minutes and remix again.

Application

Apply the mixture using a suitable spraying unit or with Tyrolean machine manually till you reach the required thickness (2 to 3 mm).

Curing

The sprayed coat should be cured for a minimum of 2 days by keeping the entire sprayed area wet all day.

Cleaning

Tools and equipment should be cleaned with water immediately after use. Hardened material should be removed mechanically.

Recommendations

  • In case of application in summer season, it is strongly recommended to spray the concrete walls one hour before applying DASHBOND in order to reduce surface temperature
  • In case of application on treated concrete with curing compound, concrete containing micro silica or AAC (Autoclaved Aerated Concrete) blocks, contact COLMEF’s Technical Department for proposed technical recommendation
Additional Information
Health & Safety

DASHBOND is a cement-based product.

 

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
OTHER PRODUCTS
More Products from this section
Monneli Dashbond SP

High Quality Spatter Dash Bond Coating

Monneli Dashbond SPX

Superior Quality Spatter Dash Bond Coating

Monneli Dashbond STR

Superior Quality Spatter Dash Bond Coating

Monneli Neofil BL

Normal Block Laying Mortar

view more
RANDOM PRODUCT
Monneli Sealprime NP

Non-Staining Primer for Non Porous Joints

Uses
SEALPRIME NP is used for priming non-porous substrates such as:
Glossy tiles
Glass
Galvanized surface
Stainless Steel
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map