Concrete Repair

Epoxy Based Repair Products

Monneli Epofinish C

Fairing Coat Solvent Free Epoxy Mortar

Uses
EPOFINISH C is designed to provide repairs to surfaces in different situations, such as:
Crack repairs in structural components, like bridges, industrial structures, columns, beams, foundations, walls and floors slabs
Filling pinholes prior to over coating
General re-profiling over large areas
Dowel bars anchoring
Bolt pocket, filling
Used as adhesive to fix slip brick to concrete
Repair surface defects on steel bridges bearings
Used as bedding mortar for bridge beams or steel bridges bearing
Used as mortar bedding in manhole chambers
General re-profiling over large areas
back to Concrete Repair
Technical Information
Product Description

EPOFINISH C is a solvent free, two components, easily workable epoxy mortar EPOFINISH C is based on a combination of epoxy resin and specially selected fillers.

 

EPOFINISH C is Thixotropic and suitable for bedding, gap filling, concrete repair and for leveling minor imperfection in concrete surfaces between up to 6mm.

Advantages
  • Non shrink, solvent free product
  • High mechanical strength, abrasion and impact resistance
  • High chemical resistance against oils, greases, salt, petroleum and mild acids and alkalis, sewage, ammonia
  • High corrosive resistance
  • Excellent adhesive to concrete substrates
  • Low viscosity, non-slump. Can be easily applied on vertical and overhead surfaces
  • Pre-measured proportions, easy to mix and apply
Packaging, Coverage / Consumption

Packaging:

EPOFINISH C is supplied in 8 kg and 4 kg kit

 

Consumption:

0.60 m2/kg when applied at 1 mm thickness.

Shelf Life & Storage

Storage:

Store in original, unopened pack in covered, dry store. Avoid direct exposure to sunlight. Do not keep in stores with temperature less than +5ºC or more than +30ºC.

 

Shelf life:

It has a shelf life of 12 months if stored as recommended.

Colors
Light grey
Technical Properties
PROPERTIES RESULTS
Color  Light grey 
Solid content  100% 
VOC 4.3 g/L 
Pot life at 25ºC >60 minutes
Compressive strength 7 days  (ASTM C579) >65 N / mm²
Flexural strength       (ASTM C 580) >39 N / mm²
Tensile strength      (BS6319 Pt.7) >20 N / mm²
Over coating time After 24 hours
Chemical resistance Resistant to oils, bleach, fats, petrol, sea water, dilute mineral acids and solvents, sewage, urine, sulphur gases, amonia
All values are subject to 5-10 % tolerance

 

Application Information
Instructions for use

Surface Preparation

The substrate must be clean, sound, free from grease, friable material, curing compound, etc. Dust should be removed by brush or compressed air.

All necessary repairs for wide cracks, degraded concrete, expansion joints, etc. should be made using one of the recommended range of concrete repair products before start to apply EPOFINISH C.

Mixing

Stir the hardener and base separately. Empty the hardener content into the base container and mix the two components thoroughly, till a uniform homogeneous paste is obtained. For perfect mixing, a low speed electric motor attached with a suitable paddle is recommended.

Application

Apply the mixed product using a trowel, scraper or filling knife. EPOFINISH C is a thixotropic workable product which makes it easier to obtain a smooth finished surface. Once the applied layer is cured, abrade slightly and clean from dust using compressed air before applying epoxy coating or finishing paint. 

EPOFINISH C is designed to filling pin holes and to reprofiling and leveling irregularities in concrete surfaces prior to applying any epoxy coating system. Application thickness depends on substrate profile. The thickness range will be between 3 – 6 mm.

Cleaning

Tools and equipment should be cleaned with SOLVENTE 10 immediately after use. Hardened material should be removed mechanically. Spillages
should be absorbed with sand or sawdust and disposed of in accordance with local regulations.

Recommendations

  • Do not use during rainy days or if temperature is less than +5°C.
  • Application should not be carried out when atmosphere humidity exceeds 90%, or when the surface to be coated is less than +3°C above the dew point.
Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary. In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.25Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofinish F

Fairing Coat Solvent Free Epoxy Mortar (3mm or less)

Monneli Epomax

Epoxy Thixotropic Adhesive for Structural Gluing

Monneli Epomort GP

General Purpose Epoxy Mortar

Monneli Epomort HS

High Performance Epoxy Mortar

RANDOM PRODUCT
Monneli Neofil BLS

SULPHATE RESISTANT BLOCK & BRICK LAYING MORTAR

Uses
Neofil BLS can be mixed by hand or with any type of electrical mixer and is normally used to fill gaps between concrete and bricks.
Neofil BLS is particularly adapted for mounting regular / hollow blocks, stones and bricks on masonry structures prone to sulphate attacks from ground soil water or the construction units themselves.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map