Concrete Repair

Epoxy Based Repair Products

Monneli Eporipresa

Epoxy Bonding Agent

Uses
Casting resumption between fresh and old concrete
Casting resumption of damaged industrial flooring
Casting resumption of plasters
Sealing of cracks or fissures of cement screeds, concrete with steel gluing, roads, bridges, pavements loading bays and factories
Internal and external applications.
back to Concrete Repair
Technical Information
Product Description

EPORIPRESA is a two component epoxy adhesive which is used as a bonding agent. It is solvent free, with thixotropic effect, formulated with the purpose of guaranteeing a structural adhesion between fresh and old concrete.

Advantages
  • Solvent free, therefore can be used in closed areas
  • High mechanical and bonding strength
  • Impermeable and no shrinks after polymerization
  • It adheres perfectly to various construction materials, including concrete, stone, iron, etc.
  • Adhesive bond to concrete will always exceed the tensile strength of the host concrete
  • Resistant to most alkalis and diluted acids
Packaging, Coverage / Consumption

EPORIPRESA is supplied in 4 Liter kit of two components

Consumption: For casting resumption, the consumption varies from 3.5-4 m²/Liter according to the irregularities of the surface.

Shelf Life & Storage

Store the product in a dry covered place with a temperature between +5°C and +30°C. If stored properly in original package, the shelf life will be 12 months.

Technical Properties
Color

Green

Density

1.2 kg/L

Pot Life

150 minutes

VOC

2.0 g/L

Tensile strength (ASTM D638)

36 N / mm²

Compressive strength (ASTM D695-96)

55 N / mm²

Slant Shear Strength (ASTM C882)

14 N / mm²

Adhesive strength

> 2.5 N/ mm²

Water absorption (ASTM D570)

< 0.05 %

Temperature of application

+5ºC to +35ºC

Complete hardening

5 days at 30 ºC

Maximum overlay time at 25 ºC

20 hours

Adhesion Characteristics Breakdown flexure test on the casting resumption executed with EPORIPRESA / Breakdown traction test on casting resumption executed with EPORIPRESA

Breakdown of concrete at 100% / Breakdown of concrete at 100%

Application Information
Instructions for use

Mixing

EPORIPRESA is supplied in two pre-weighed packs (Component A – Base and Component B – Hardener) which are ready for immediate in-situ use.

Stir in both components before use. Transfer the entire contents of component B (Hardener) into the component A (Base) can and mix with low speed drill and paddle (200 – 300 rpm) for 2 – 3 minutes till obtaining a mix with uniform consistency. Scrape the sides and bottom of the can during mixing to ensure homogeneity.

Application

The product must be applied with brush or spray on the whole surface. Extra care to be taken to ensure that the whole repair area is covered in order to obtain perfect adhesion.

EPORIPRESA should be tacky before the new concrete, screed or mortar is placed. The maximum over lay time should also be carefully observed.

If the maximum over lay time is missed, then EPORIPRESA must be mechanically removed and a fresh application should be made.

The new casting of fresh concrete must be executed immediately. For the fissures superior to 0.5 mm, the product can be simply poured.

Cleaning

Tools and equipment should be cleaned with SOLVENTE 10 from Colmef immediately after use. Hardened material should be remove mechanically. Spillages should be absorbed with sand or sawdust and disposed of in accordance with local regulations.

Recommendations

  • Do not use during rainy days or if temperature is less than +5°C
  • Application should not be carried out when atmosphere humidity exceeds 90%, or when the surface to be coated is less than +3°C above the dew point
  • Do not expose packing to the direct sunrays
Surface Preparation

Surface must be perfectly clean and compact. Inconsistent parts, varnishes, grease, laitance, algae, must be eliminated through sand blasting or brushing before applying EPORIPRESA. All dust, unsound material, plaster, oil, paint, grease, corrosion deposits, curing compound must be removed.

New concrete or cementitious surfaces should be allowed to cure and have moisture content not exceeding 5%. Old or existing floor should be refurbished mechanically to ensure clear sound substrate.

Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.54Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofinish C

Fairing Coat Solvent Free Epoxy Mortar

Monneli Epofinish F

Fairing Coat Solvent Free Epoxy Mortar (3mm or less)

Monneli Epomax

Epoxy Thixotropic Adhesive for Structural Gluing

Monneli Epomort GP

General Purpose Epoxy Mortar

Monneli Epomort HS

High Performance Epoxy Mortar

RANDOM PRODUCT
Monneli Insuwrap 1000 WM-FB

1.0 mm thick with Fleeceback PVC Membrane for covered roofing system

Uses
Waterproofing of covered Roofs and podiums
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map