Industrial Flooring

Heavy Duty Industrial Flooring System

Monneli Epofloor SL (IF)

Solvent-Free Epoxy Self Leveling Topping (0.8 – 2.0mm) for Concrete Floors

Uses
EPOFLOOR SL (IF) has a high gloss finish and is used in various installations such as:
Airport hangars (resistant to Skydrol)
Workshops
Warehousing and storage facilities
Chemical and pharmaceutical factories
Food factories and slaughterhouses
Schools and office buildings
Showrooms
back to Industrial Flooring
Technical Information
Product Description

EPOFLOOR SL (IF) is a solvent free self-leveling floor topping based on formulated epoxy resin and curing agents specially selected for their ability to be applied and cured in warm temperatures.

Packaging, Coverage / Consumption

Packaging:

EPOFLOOR SL (IF) is supplied as a pre-measured kit depending on customers’ requirements.

Our standard packaging is 4 Liter & 15 Liter kit.

Shelf Life & Storage

Storage:

Keep in tightly closed containers and in sheltered and dry place with a temperature between +5°C and +35°C. In these conditions it maintains its characteristics unchanged for 12 months

Technical Properties
PROPERTIES RESULTS
Solid content 100%
Recommend DFT / coat  0.8 – 2.0 mm 
Kit size  4 Liters 
Theoretical coverage  2.0 – 5.0 m² / 4 Liter Kit  
Kit size   15 Liters 
Theoretical coverage 7.5 – 18.75m/ 15 liter Kit
Pot life at 18°C 90 minutes
Pot life at 30°C 45 minutes 
Thin layer (3mm) Dry time at 25°C 5-6 hours
Thin layer (3mm) Dry time at 40°C   5 hours 
Mixing ratio (by weight) 
Hardener 1.0
Base 7.7
Mixed density at 20°C 1.8 kg/L
Max recoat/Topcoat time at 125°C 24 hours
Application maximum relative humidity 75 %
Compressive strength  (ASTM C579) >80 N / mm²
Bending strength (ASTM C580) >25 N / mm²
Tensile strength (ASTM C307) >15 N / mm²
Bond strength to concrete (ASTM D4541) >2.0 N / mm²
Taber abrasion  (ASTM D4060 CS17 Wheels) 50 mg loss / 1000 cycles
Water absorption  (ASTM D413 ) (maximum) 0.001%
Porosity with no sealer NACE Sand TM-01-74 0
Hardness shore D 85
All values are subject to 5-10% tolerance 
Application Information
Instructions for use

Components

n EPOFLOOR SL (IF) contains resin (Component A), hardener (Component B):

n EPOFLOOR SL (IF) resin (Component A) is a low viscosity standard coloured base which contains fillers and pigments.  

n EPOFLOOR SL (IF) hardener (Component B) is a low viscosity and low color hardener which, after mixing with the base, is less-yellowing and can be applied at 75% humidity. The hardener provides excellent chemical and abrasion resistance.

Surface preparation

The concrete must be at least 28 days old. The concrete must be free from loose matter, oil and dirt before starting surface preparation.

The best method to prepare the surface is dry grinding using a specialized planetary grinder. Before grinding, the surface must be free from any degreasing or cleaning chemicals which may have been used. At the end of grinding, the surface should be flat.

Surface irregularities and blow holes shall be repaired with EPOFINISH IF.

When the filler is hardened, grinding and leveling of the patched area is recommended to ensure a good finish.

Ensure dust is removed from the surface using an industrial vacuum.
For best finish and adhesion, treat the surface with PRIMER POXY IF. In case the surface is very absorbent, apply a second coat of primer within the allowed recoating time.

Application Thickness

A thickness of 0.8 – 2.0 mm per coat over a primer is recommended.

Items Needed

n Multi-speed drill fitted with a mixing paddle.

n Good quality medium haired non-shedding roller, suitable for epoxy application. Ensure that all loose hairs on the roller have been removed before use

n 7” Screed rake

n Spike roll and spike shoes

n Clean bucket, 2” brush and SOLVENTE 10 to clean the equipment

Method

Adjust the rake to the desired thickness.

Using a drill and a paddle at low speed, stir the resin (Component A) for 1 min. Slowly add the hardener (Component B) and increase mixing speed. Mix for 1-2 minutes, ensuring proper mixing between the resin and the hardener components, until a completely homogeneous streak free mix of uniform color is obtained.

Pour the mix onto the floor immediately and spread using the rake. After about 5 minutes use the spike roll to remove all entrapped air.

Cleaning

Clean equipment with SOLVENTE 10. In case of spillage, use fine silica or cement to absorb the spill and dispose of according to local regulations.

Additional Information
Health & Safety

Study the MSDS of the product before use or storage.

 

EPOFLOOR SL (IF) is not regulated per the “Directive 67/548/EEC EU Dangerous Materials List” so no special labeling is needed.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.29Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofinish IF

Solvent-Free Repair Mortar for Concrete Floors

Monneli Epofloor E 250 (IF)

Solvent-Free Epoxy Topcoat for Concrete Floors

Monneli Epofloor SL (IFT)

Solvent-Free Epoxy Self-Leveling Topping (2.0-4.0mm) for Concrete Floors

RANDOM PRODUCT
Monneli Elastothane WP2

Two Components Elastomeric Polyurethane Waterproofing Coating

Uses
ELASTOTHANE WP2 is designed to waterproof most applications within the building to construction industry including:
Odorless waterproofing system for bathrooms, swimming pools, kitchens, terraces, balconies, shower areas
Cold applied waterproofing for flat roofs and concrete structures, basement masonry, roof gardens, car parking
As a damp proofing course
Connected products
Monneli Epofinish IF

Solvent-Free Repair Mortar for Concrete Floors

Monneli Primer Poxy (IF)

Penetrating Solvent-Free Epoxy Primer for Concrete Floors

Monneli Solvente 10

Thinner / Cleaning Solvent

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map