Industrial Flooring

Cement Based Flooring Systems

Monneli Neocem Screed 30

Pre-mixed Floor Screed

Uses
NEOCEM SCREED 30 can be used as follows:
Can be applied on any type of support as long as it is not subjected to rising humidity, like old or new concrete and stone. It is used to level horizontal surfaces prior to laying floor coverings.
Used to produce bonded screeds in internal areas.
back to Industrial Flooring
Technical Information
Product Description

Ready to use cement based floor screed. It is a single compound formulated specially from hydraulic cement, graded aggregates, silica sand, fiber and special chemical additives. It is ideal for leveling and smoothing uneven floors prior to laying decorative floor coverings, carpets, floor tiles, or any other finishing.Ready to use cement based floor screed. It is a single compound formulated specially from hydraulic cement, graded aggregates, silica sand, fiber and special chemical additives. It is ideal for leveling and smoothing uneven floors prior to laying decorative floor coverings, carpets, floor tiles, or any other finishing. Ready to use cement based floor screed. It is a single compound formulated specially from hydraulic cement, graded aggregates, silica sand, fiber and special chemical additives. It is ideal for leveling and smoothing uneven floors prior to laying decorative floor coverings, carpets, floor tiles, or any other finishing.

Advantages
  • Excellent workability properties, good compaction
  • High strength and resistance to construction traffic
  • Eco-friendly - Low VOC
Packaging, Coverage / Consumption

Packaging:

NEOCEM SCREED 30 is supplied 50 Kg bags.

 

Consumption: 

2.0 Kg/m2 per millimeter of thickness.

Shelf Life & Storage

Storage:

Keep in sheltered and dry place with a temperature between +5°C and +35°C.

 

Shelf life:

12 months from date of production if stored properly.

Colors
Grey
Technical Properties
PROPERTIES RESULTS
Appearance Powder
Color Grey
Density at 25°C  2.0 kg/L 
Workable time at 25°C >30 mins
VOC 0.2 g/L
Aggregate size 0-5mm
Compressive strength at 28 days (BS EN 196-1) 25 N / mm²
Flexural strength at 28 days (BS EN 196-1) 7 N/mm²
Tensile adhesion strength  (BS 1881) 2.5 N/mm²
BRE screed test (BS 8204 Pt.1) 2.1 mm
Shrinkage test (ASTM C531) 0.02%
Open to foot traffic at 25°C 48 hours
Full traffic use at 25°C 28 days
Service temperature -5°C to +80°C
All values are subject to 5-10 % tolerance  
Application Information
Instructions for use

Surface preparation

The base concrete should be sound, clean free from loose material, lime, gypsum, plaster, grease laitance, dirt curing compound. The surface must be well prepared for bonding by scabbing to expose the coarse aggregate. Fix any screed battens to level. The surface should be swept to remove any loose material and wetted with clean water if the screed is placed in direct contact with the base.

Priming

NEOCEM SCREED 30 can be laid as a bonded screed by applying SBR Bonding Slurry to prepared concrete substrate as a bonding and priming layer.

To prepare the SBR bonding slurry, mix 1 part of SBR LATEX RIPRESA, a SBR with 2 parts of clean water and add 3 parts by weight of fresh cement and mix until a smooth consistency is prepared.

Scrub the mixed slurry into the concrete surface, while the slurry is not yet dry; apply NEOCEM SCREED 30 in order to ensure good adhesion with the substrate.

Mixing

Pour into a container 6-7 liters of water for 50 Kg bag of NEOCEM SCREED 30. Add the powder screed to the water and mix with a low speed electric drill fitted with a suitable paddle, until a uniform, lump free consistency mix is achieved. No further water should be added to the mix particularly once its start to set.

Application

Pour the mixed product onto the surface and spread to the level about 10 mm above the bottom i.e.: giving it a surcharge. Then tamp down the screed heavily to the level to give a full compaction. Strike off excess screed material until the top level (above the batten) by running a straight edge ruler alongside it.

Fill any slightly low areas, re-compact and rule out. Finish the section of the screed laid by wood float and steel trowel.

Protect the floor after leveling the mix from direct sunlight, high winds or rain.

It is possible to apply flooring material on top of NEOCEM SCREED 30 (such as ceramic, carpet, etc.) after nearly 7 days (depending on the thickness, humidity and weather conditions).

Curing

Curing of the completed floor shall be carried out using a combination of damp hessian and polythene sheeting for a period of no less than 3 days.

Cleaning

Tools and equipment should be cleaned with water immediately after use. Hardened material should be removed mechanically.

Recommendations

  • During summer season or temperature higher than 35oC, working area should be covered to prevent the direct sun effects. Keep equipment cool and use cool water.
  • Protect the freshly applied NEOCEM SCREED 30 from direct sunlight and/or strong drying wind.
  • NEOCEM SCREED 30 should be cured for minimum 3 days with clean water
  • Most floor covering can be laid after 7 days
  • When applying the screed over tongue and groove timber floors or other surfaces, it is recommended to reinforce the screed with expanded metal or galvanized wire mesh.
  • Do not use where negative hydrostatic pressure is evident (i.e. rising damp)
Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Autolivellante

Self-Levelling Cementitious Mortar

Monneli Autolivellante 10

Self-Leveling Cementitious Mortar

Monneli Autolivellante 30

Self-Leveling Cementitious Mortar

Monneli Betolite

Light Weight Screed

Monneli Betolite*

Light Weight Screed

view more
RANDOM PRODUCT
Monneli Rasante P20-F

Fibre Reinforced Cementitious Plaster

Uses
RASANTE P20-F is recommended for plastering on the following:
Block walls
Ceilings
Bricks
Concrete surfaces
Connected products
Monneli SBR Latex Ripresa

SBR Bonding Agent for Cement Mortar & Concrete

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map