Protective Coating

Anti-Carbonation Coating

Monneli Acryfil

Ready-mixed, Acrylic Pinhole Filler

ACRYFIL can be used as follows:
Can be used for filling pin holes, and levelling minor irregularities in the substrate, prior to the application of MANTOCOLOR, or any other acrylic based material.
Can be used in the repair of cementitious, gypsum, spray and normal plaster surfaces.
back to Protective Coating
Technical Information
Product Description

ACRYFIL is a ready-mixed putty based on a blend of acrylic polymer and graded fine filler. ACRYFIL had been specially developed for use with MANTOCOLOR.

  • Single component, easy to use
  • Minimal shrinkage
  • Good adhesion to the substrate
  • Non toxic
  • Vapour permeable
  • Does not flake off or de-laminate
Packaging, Coverage / Consumption


ACRYFIL is supplied in 25 kg container.



0.2 – 0.4 kg/m² (depending on substrate conditions).

Shelf Life & Storage


Keep the product in a dry and covered place away from direct sunlight into the original well-closed packaging. A shelf life of 12 months is expected if stored as recommended.

Technical Properties



White paste

Density at 25°C

1.8 kg/L

Application temperature

5⁰C to 35⁰C

All values are subject to 5-10 % tolerance

Application Information
Instructions for use

Surface preparation

The surface must be solid, compacted, sound, uncontaminated, free from dust, curing compound, oil, and grease before applying the product.
ACRYFIL can be applied to existing coating. In order to determine the compatibility with the existing coating, it maybe necessary to carry out adhesive test.


It is recommended to apply IDROSIL XS, a Silane-Siloxane penetrating primer for dusty or flaking surfaces and in some cases on the existing coating. For further information contact Colmef Technical Department.


ACRYFIL should be mixed well before use.


Apply ACRYFIL in a thin layer on the prepared surface. Material should be tightly trowelled on the surface to ensure that all pin holes and irregular areas are completely filled. If a second layer is needed, wait till the first layer is dry. Total recommended thickness of ACRYFIL should not exceed 1mm.

Once the final layer has dried, it may be sanded lightly to achieve a full smoothness. Before applying the overcoating be sure that the coated surface is not contaminated and free from dust or cement debris as this will affect the top coat adhesion with the surface.


Clean the used tools with water immediately after completing the job and before the product dries.

Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.


In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.


If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
reference projects
More Products from this section
Monneli Mantocolor S

Solvent Based Styrene-Acrylate Protective and Decorative Coating

Monneli Mantocolor W

Elastomeric, Protective, Anti-Carbonation & Waterproof Coating

Monneli Insuwrap 2500 TNL-FB

2.5 mm thick Fleece-back PVC Membrane for Underground Structures & Tanking System

Waterproofing of basements, tunnels and other underground structures
Connected products
Monneli Idrosil XS

Solvent Based Silane-Siloxane Penetrating Water Repellant Treatment

Monneli Mantocolor W

Elastomeric, Protective, Anti-Carbonation & Waterproof Coating

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map