Surface Treatment

Curing Compounds

Monneli Betocure S

Water based concrete curing compound

Uses
BETOCURE S is used as an effective and economical curing agent compared to the traditional Hessian, water and polyethylene curing system. Suitable for all types of concrete surfaces such as:
Interior and Exterior Floor Slabs
Sidewalks
Driveways
Beams and columns
Warehouse flooring
back to Surface Treatment
Technical Information
Product Description

BETOCURE S is a clear liquid based on sodium silicate to cure, harden and seal freshly hardened concrete. It is easy to apply, leaves no residue and dries quickly

Advantages
  • Ready to use
  • Economical
  • Water based. Eco-friendly
  • Colorless and Odorless
  • Easy application and quick drying
  • Degrading over a period of time
  • Improve resistance to abrasion and corrosive action of salt and chemicals
Packaging, Coverage / Consumption

Packaging:

BETOCURE S is packed in plastic containers of 20 liters and 210 liters.

 

Coverage:

15-20 m²/liter, depending on concrete surface condition.

Shelf Life & Storage

Shelf Life:

BETOCURE S has a minimum shelf life of 12 months, provided the temperature is kept within the range of 5°C to 35°C. Prolonged exposure to direct sunlight should be avoided.

Containers should be kept sealed and airtight to prevent of moisture by evaporation.

Technical Properties
PROPERTIES

RESULTS

Appearance

Clear liquid

Density at 25°C

1.3  kg/L

VOC

1.3 g/L

Drying time at 25 °C

30 – 40 minutes

pH at 25 °C

10 - 12

Curing Efficiency (BS 7542)

75.00 %

All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Pre–application

BETOCURE S should be stirred before application. Product is ready for use directly from the drum and should not be diluted with water. BETOCURE S is not a film forming product but should fully saturate the concrete for maximum effect. Perform enough application to fully saturate the concrete without leaving puddle.

Surface should be free of water. In case of horizontal surfaces, the product should be applied as soon as the bleed water has evaporated from the surface.

Application

BETOCURE S should be applied uniformly by sprayer, brush, roller or soft bristled broom to the surface of fresh concrete. For best results, use spray for application. Application should be at the rate of 15m2/liter. The coating produces a light duty surface. It is the responsibility of the user to adjust to curing rate to properly regulate the hydration of the concrete. Two applications maybe required. BETOCURE S should be applied to newly hardened concrete immediately after demolding. It should never be applied on concrete which has started to dry out, otherwise the hydration mechanism will be seriously impaired. Do not allow compaction or vibrating acts close to the sprayed area as this will break the freshly sprayed film.

Overcoating

Over coating can be done without removal of curing compound provided the application is within the specified coverage rate.

Clean

Equipment and tools used should be cleaned promptly with water.

Recommendations

  • Use only on green or recently poured clean concrete
  • Protect areas not intended for coverage. If contact occurs, remove immediately using water and a cloth or brush
  • Do not allow the product to puddle. White residue may form if BETOCURE S is over applied
Additional Information
Health & Safety

Direct contact with the product may result in irritation of the skin and eyes. Product vapors may also cause irritation. Wear gloves and masks, wash thoroughly after handling remove any contaminated clothing and wash skin with soap and water.
Remove ignition sources prior to use. Accidental eye contact, wash with plenty amount of water and seek immediate medical help.
Refer to Material Safety Data Sheet for complete health and safety information.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.34Mb)
OTHER PRODUCTS
More Products from this section
Monneli Betocure AR

Acrylic based concrete curing compound

Monneli Betocure R

High Efficiency Resin Based Curing & Sealing Compound

Monneli Betocure S125

Water Based Concrete Curing Compound

Monneli Betocure W

Wax Based Concrete Curing Compound

RANDOM PRODUCT
Monneli Betocure R

High Efficiency Resin Based Curing & Sealing Compound

Uses
BETOCURE R provides high curing efficiency. It can be used in wide range of applications such as:
Factory floors and warehouses
High rise buildings
Floor slabs and columns
Multilevel parking decks
Driveways and parking areas
Industrial flooring
Ports
Airport hangars
Self-curing primer systems and subsequent coverings
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map