Mortar Specialties

Gypsum Based Mortar

Monneli Rasante G-10

Gypsum Based Plaster for Thickness Up To 6 mm

Brick walls covered with gypsum
Thermo-acoustic insulating panels
Concrete panels
back to Mortar Specialties
Technical Information
Product Description

RASANTE G-10 is a gypsum based powder product, modified with additives and special synthetic resins which gives the product excellent characteristics of adhesion to the support and easy workability.

  • Can be applied either vertically or horizontally on internal applications
Compiliance Standard
  • ASTM 387, 28, 207 Type N
  • BS 5492, 1191, 890
  • BS EN 1015
  • DIN 18550
Packaging, Coverage / Consumption

RASANTE G-10 is supplied in 40kg multilayer bags.

Consumption: 1.2-1.4 Kg/m² per millimeter of thickness.

Shelf Life & Storage

Store in dry covered place in the original closed bags. In these conditions, the product shelf life is 6 months from the date of production.

Technical Properties



Off white

Density at 25°C

1.4 kg/L



Pot life at 25ºC

40 minutes

Compressive Strength at 28 days

4 N/mm2

Flexural Strength at 28 days

1 N/mm2

Temperature of application

+5ºC to +35°C

Time to attend before exploitation

24 hours

Possible thickness per coat

up to 6 mm

Harmfulness CEE 88/379


Application Information
Instructions for use


To prepare the mixture, pour a clean water into a container and add RASANTE G-10, with ratio 45-50%, (a bag of 40 Kg and about 18-20 Liters of water), then mix with a mixer at low number of turns, till you get a homogeneous paste free from clots.

The mixture remains workable for about 40 minutes after mixing.


RASANTE G-10 must be applied in a single layer of thickness up to 6mm using a smooth steel trowel.

Applied material should be sponged and finished off with a damp steel trowel to achieve a smooth finish. Apply a thickness not more than 6mm and do not apply any top coat before RASANTE G-10 layer dried completely. The product does not require any curing with water.


Tools and equipment should be cleaned with water immediately after use.

Hardened materials should be mechanically removed

Surface Preparation

The substrate should be free of loose particles, dust, dirt, grease, oil or paint.

Before applying RASANTE G-10 saturate the surface with water and wait for the evaporation of excess water before applying the mix.

Additional Information
Health & Safety

RASANTE G-10 is a gypsum-based product.


During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.


In case of contact with skin, rinse with water and again wash thoroughly with soap and water.


In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.


If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.06Mb)
More Products from this section
Monneli Neofil G12

Gypsum Board Adhesive

Monneli Rasante G-15

Gypsum Pre-Mixed Plaster for Thickness up to 20mm

Monneli Kretesil CR

Crystalline Waterproofing Mortar

Industrial processing plants
Parking decks
Road decks
Cellars and concrete roofs, etc.
KRETESIL CR can also be used as effective waterproofing system for the following:
Swimming pools
Reservoirs and water tanks
Water treatment areas
Canals, harbors and dams
Concrete pipes
Sea defense walls
Bridge decks
Retaining walls
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map