Surface Treatment

Curing Compounds

Monneli Betocure S125

Water Based Concrete Curing Compound

Uses
BETOCURE S125 is an effective and economical curing agent compared to the traditional Hessian, water and polyethylene curing system. Suitable for all types of concrete surfaces such as:
Interior and exterior floor slabs
Sidewalks
Driveways
Beams and columns
Warehouse flooring
back to Surface Treatment
Technical Information
Product Description

A clear liquid based on sodium silicate to cure, harden and seal freshly hardened concrete. It is easy to apply, leaves no residue and dries quickly.

Advantages
  • Ready to use
  • Water based. Eco-friendly
  • No VOC
  • Colorless and odorless
  • Lowers moisture vapor emission
  • Easy application and  quick drying
  • Degrading over a period of time
  • Improve resistance to abrasion and corrosive action of salt and chemicals
  • Economical
Technical Properties
PROPERTIES RESULTS
Appearance Clear liquid
VOC Negligible 
Drying Time at 25°C  30 – 40 minutes 
pH at 25°C 10 - 12
Curing efficiency (BS 7542) 75.00 %
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Pre-Application
BETOCURE S125 should be stirred before application. Product is ready for use directly from the drum and should not be diluted with water. BETOCURE S125 is not a film forming product but should fully saturate the concrete for maximum effect. Perform enough application to fully saturate the concrete without leaving puddle.
Surface should be free of water. In case of horizontal surfaces, the product should be applied as soon as the bleed water has evaporated from the surface.

Application
BETOCURE S125 should be applied uniformly by   sprayer, brush, roller or soft bristled broom to the surface of fresh concrete. For best results, use spray for application.
Application should be at the rate of approx. 15m2/liter. The coating produces a light duty surface. It is the responsibility of the user to adjust to curing rate to properly regulate the hydration of the concrete. Two applications maybe required. BETOCURE S125 should be applied to newly hardened concrete immediately after demolding. It should never be applied on concrete which has started to dry out, otherwise the hydration mechanism will be seriously impaired. Do not allow compaction or vibrating acts close to the sprayed area as this will break the freshly sprayed film.

Overcoating
Over coating can be done without removal of curing compound provided the application is within the specified coverage rate.

Cleaning
Equipment and tools used should be cleaned promptly with water.

Recommendations

  • Use only on green or recently poured clean concrete
  • Protect areas not intended for coverage. If contact occurs, remove immediately using water and a cloth or brush
  • Do not allow the product to puddle. White residue may form if BETOCURE S is over applied.
Additional Information
Health & Safety

BETOCURE S125 does not fall into hazardous classification of current regulation. However, it should not be swallowed or allowed to come into contact with skin or eyes in either spray or bulk form. Splashes on the skin should be removed with water. In case in contact with eyes, rinse immediately with water and seek medical attention.

If swallowed, seek medical attention immediately. Wear suitable protective clothing, gloves and goggles

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.25Mb)
OTHER PRODUCTS
More Products from this section
Monneli Betocure AR

Acrylic based concrete curing compound

Monneli Betocure R

High Efficiency Resin Based Curing & Sealing Compound

Monneli Betocure S

Water based concrete curing compound

Monneli Betocure W

Wax Based Concrete Curing Compound

RANDOM PRODUCT
Monneli Conmastic

Highly Rubberized Bitumen Sealant

Uses
Sealing low movement joints in concrete pavements, bridges, building structures, etc.
Sealing joints at waterproofing membrane termination grooves, filling gaps and sealing between brick work and roof flashing
Sealant for tiles, slates, manhole covers, around pipe entries, pipe joints, seawalls, subways and basement structures
Filling cracks and in roofing materials such as felt, lead, zinc, steel, corrugated cement sheets
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map