Tile Adhesives

Cement Based Adhesive

Monneli Tile Glue Ultra

Waterproof Polymer Modified Tile Adhesive

Uses
NEOFIL TILE GLUE ULTRA is used for fixing of wall and floor tiles in interior and exterior applications especially to those exposed to permanently wet condition.
Kitchens, Shower rooms & Regular rooms
Swimming pools & Fountains
Residential, Commercial and Industrial structures
Tiles: ceramic and porcelain
back to Tile Adhesives
Technical Information
Product Description

NEOFIL TILE GLUE ULTRA is a polymer modified cementitious tile adhesive. It is water/weather resistant and does not contain asbestos nor any other harmful components.

Advantages
  • Enhanced bond and tensile strengths
  • Water resistance
  • Eco-friendly, Economical
  • Good open time and slip resistance (non sagging)
  • Formulated to suit Middle East conditions
Compiliance Standard
  • ISO 13007 / EN 12004: C2T
  • ANSI  A 118.4 (when mixed with Elastokol)
  • EN 1346 / EN 1348
Packaging, Coverage / Consumption

Packaging:

NEOFIL TILE GLUE ULTRA is packed in 25 kg bags.

 

Consumption:

Approx. 2.5  to 4.5kg NEOFIL TILE GLUE ULTRA  per m² using notched trowel on smooth surface. Consumption will vary according to type of tiles and support condition.

Shelf Life & Storage

Storage:

Store in dry covered place in the original closed bags and shelf life is 12 months if stored as recommended.

Technical Properties
PROPERTIES

RESULTS

Appearance

Grey or White Powder

Density
Dry          1.55 kg/L
Wet     1.70 kg/L

 

VOC

3.0 g/L

Water resistance

Excellent

Slip resistance

Excellent

Open time

Approx. 20 minutes

Workable time

45 minutes

Wall grouting

After 10 hours

Floor grouting

After 24 hours

Shear strength

1.4 N/mm²

Adhesion strength (EN 1348)
Initial adhesion at 28 days 1.4 N/mm²      
Adhesion after heat ageing 1.0 N/mm²            
Adhesion after water immersion 1.0 N/mm²      
Adhesion after freeze thaw cycle 1.0 N/mm²      

 

All values are subject to 5-10 % tolerance

Application Information
Instructions for use

Surface preparation

All surfaces should be sound, clean & uncontaminated. This preparation should leave an exposed concrete surface free from dust, loose particles, deletrious matter, oil, grease, chemical films & other contaminant.
All loose particles of mortar, paint, etc. must be physically removed.
Concrete or blockwork: should be allowed to cure sufficiently so that all shrinkage movements take place before fixing tiles.
Gypsum supports: must be treated with PRIMER A16. Should not have a percentage of humidity more than 10%.

Mixing
Place  4.8 – 5.0 liters of cold, potable water (or ELASTOKOL as needed) in the mixing bucket and add slowly 25 kg bag of NEOFIL TILE GLUE ULTRA under continuous mixing till a uniform lump free consistency mix is achieved. For mixing process, a slow speed drill (200- 300rpm) fitted with a suitable paddle is recommended.
Allow the obtained mix to stand for 3 minutes and then remix before application.

Application
Spread NEOFIL TILE GLUE ULTRA on the substrate to a uniform thickness using a toothed spatula, the first pass with its straight edge and the second pass immediately after, to the desired thickness using the toothed part.
Place the tiles onto the adhesive bed. Apply sufficient pressure on the tile during fixing it with slight twisting movement in order to ensure good contact with the adhesive.
In case of large size tiles, it is necessary to spread the adhesive also to the backside of the tile and then place the tiles into the adhesive bed.
Apply enough material that can be tiled during the adhesive’s open wet time.
Spreading large areas may result in drying the adhesive before tiles can be fixed causing poor adhesion.

Finishing
Remove excess adhesive with damp cloth before the material has set.  Joint grouting between tiles may be commenced 10 hours after tiles have been laid on the walls and 24 hours after tiles are laid on the floors.

Cleaning
Tools and equipment should be cleaned with water immediately after use. Hardened materials should be mechanically removed.

Recommendations

  • To achieve improve adhesion strength, it is recommended to replace water with ELASTOKOL
  • Stiffened mortar  must neither be diluted with water nor with fresh mortar
  • Do not use NEOFIL TILE GLUE ULTRA  on metal or non-absorbing surfaces
  • Do not apply NEOFIL TILE GLUE ULTRA  in rainy weather, high winds and sand storms
  • Do not apply under direct sun
  • Keep equipment cool and use cold water
  • Porosity of tiles and substrates has significant effect on adhesive strength of tiles
Additional Information
Health & Safety

NEOFIL TILE GLUE ULTRA can be harmful to skin as it contains cement powders which may releases alkalis when mixed with water.
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.
In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.
If ingested, obtain medical attention immediately.
Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
OTHER PRODUCTS
More Products from this section
Monneli Adercol

Two Component Fast - Setting Cementitious Tile Adhesive

Monneli Arredo Colla

Cementitious Adhesive for Natural & Artificial Stone

Monneli Elastokol

Synthetic Latex Additive for Tile Adhesive

Monneli Maxicol

Polymer Modified Floor Tile Adhesive Up To 15 mm Thick Mortar

Monneli Maxicol T50

THICK BED TILE ADHESIVE FOR INTERIOR & EXTERIOR USE

view more
RANDOM PRODUCT
Monneli Insuwrap PVC 3000 TNL

3.0 mm thick PVC Membrane for Underground Structures & Tanking System

Uses
Waterproofing of basements, tunnels and other underground structures
Connected products
Monneli Neofil F7

High Performance Water Resistant Ceramic Tile Adhesive

Monneli Neofil F8

High Performance Thin Set Waterproof Polymer Modified Tile...

Monneli Neofil Pool Fix

High Performance Cementitious Adhesive for Swimming Pools Tiles

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map