Joint Sealants

Sealants

Monneli Acryseal

Acrylic Sealant

Uses
ACRYSEAL is used for:
Sealing joints around doors and windows frames, skirting, architraves, etc.
Sealing joints subject to moderate movement of expansion and contraction
Can be used as a crack filler in plaster or concrete
back to Joint Sealants
Technical Information
Product Description

ACRYSEAL is a single component, multi purpose sealant based on acrylic co-polymer resins which, when cures, forms a flexible sealant. ACRYSEAL sealant is resistant to abrasion and weathering and also has a very good adhesion to most porous surfaces.

Advantages

n Single component, ready to use

n High adhesion and bonding properties

n Paintable with emulsion and alkyd paints

n Weather resistance

n Easy to apply

n Economical

Compiliance Standard

n ASTM C 834

Packaging, Coverage / Consumption

Packaging:

ACRYSEAL is supplied in 5kg plastic and 280ml. cartridge containers

 

Consumption: 

1 Kg of ACRYSEAL will fill 4.5 linear meter for a joint size of 10 mm (depth) X 15 mm (width)

Shelf Life & Storage

Storage:

Store the product in dry closed place with temperature between 10 to 25ºC. Storage above this temperature may reduce shelf life. The product maintains its stability for 12 months.

Colors
White (Other colors are available upon request)
Technical Properties
PRODUCT RESULTS
Colour White (other colors available upon request)
Colour change  None 
Density at 25°C  1.45 kg/L 
VOC 7.1g/L
Full Cure 7 days
Elongation at break 250%
E-modulus 1.10 MPa
Weather resistance Excellent
Shrinkage < 15%
Movement capacity ± 15%
Service temperature -5°C to +80°C
Water absorbency Minimal
Maximum joint width 25 mm
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface Preparation

Joint substrate should be sound, clean and free from loose material, or chemical products, oil or grease.

Remove or round any sharp edges or corners in order to optimize the adhesion.

Application

For porous or very dry substrates, it is recommended to dilute Acryseal with water (1:3 by volume) and apply by brush in thin coat as primer.

Allow the primer to become tack free before application of the sealants.
For neat and clean job, use masking tape around the joint edges before applying the sealant. Remove the tape immediately after the sealant is applied.

ACRYSEAL can be applied by caulking gun or a suitable putty knife or spatula. Press the sealant into the joint to ensure a firm and full contact with the joint surface and to avoid bubble trap.

Cleaning

Tools and equipment should be cleaned with water immediately after use. Hardened material should be removed mechanically.

Recommendations

ACRYSEAL is not recommended for:

n Joints having high degree of movements

n Damp & contaminated surfaces

n Heavily trafficked floor joints

Additional Information
Health & Safety

Keep ACRYSEAL away from the source of ignition. During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly. If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Acryseal AC

Single Component Gun Grade Sealant

Monneli Conmastic

Highly Rubberized Bitumen Sealant

Monneli Elastoseal CTP

Coal Tar Extended Polyurethane Joint Sealant

Monneli Elastoseal EPU

Heavy Duty Epoxy Urethane Joint Sealant

Monneli Elastoseal PS

Two Component Polysulphide Sealant

view more
RANDOM PRODUCT
Monneli Elastothane 100

Elastomeric Single Component Aliphatic Polyurethane Waterproofing Membrane

Uses
ELASTOTHANE 100 can be successfully applied on tiles, concrete, cement roof tiles, wood and galvanized steel.
The seamless membrane can be used as an impervious waterproof coating on the following:
Roofs
Sunken slabs
Concrete domes
Profile sheets
Kitchen and bathrooms
Balconies and patios
Basements
Swimming pools and other water retaining structures, bridges and tunnels, etc.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map