Protective Coating


Monneli Armaturea A1

Aromatic Pure Polyurea

ARMATUREA A1 can be used as a protective, elastomeric membrane coating for applications in or on:
Industrial facilities
Cold storage facilities
Warehouse floors
Below grade waterproofing
Parking garage decks
Water and waste water treatment
Food processing facilities
Pulp and paper mills
Tank linings
Pickup truck bedlining
Bottling & canning factories
Walkways and balconies
Secondary containment
Mining operations
Landfill containment
Bridge deck underlays
Water parks & theme parks
Sprayed on urethane foam
Geotextile linings foundation walls & sumps
back to Protective Coating
Technical Information
Product Description

ARMATUREA A1 is a two component pure aromaticpolyurea elastomer formulated for applications in concrete lining, corrosion protection and waterproofing. ARMATUREA A1 is designed to minimize problems associated with field applications and can be applied in the most problematic of ambient conditions since it is relatively temperature and moisture insensitive.

  • Eco-friendly, zero VOC
  • Flexible, excellent elongation
  • Excellent thermal stability
  • Good chemical resistance
  • Excellent UV resistance
  • Seamless, resilient, non-cracking elastomer
  • Excellent corrosion protection
  • Low perm rate
  • Fast reactivity and cure time (No catalysts)
  • Return projects to service in 60 minutes
Compiliance Standard
  • ASTM D412
  • ASTM D624
  • ASTM D4060
  • ASTM D2240
  • ASTM D1737
Packaging, Coverage / Consumption


  • 400 Liter Kit: 200 Liters of Part A and 200 Liters of Part B
  • 38 Liter Kit: 19 Liters of Part A and 19 Liters of Part B
Shelf Life & Storage


ARMATUREA A1 should be stored in original, unopened factory containers, under normal storage conditions of 15° C to 35° C. In these conditions, prouct shelf life is 12 months from the date of production.

Standard colors are medium gray or black. Other colours available upon request.
Technical Properties



Medium gray or black

Solid content


Curing time

60 mins

Tensile strength (ASTM D412)

10 N/mm²

Elongation (ASTM D412)

> 450%

Tear strength (ASTM D624)

> 70 N/mm²

Shore A hardness (ASTM D2240)


Shore D hardness (ASTM D2240)


Flexibility 1/8” Mandrel (ASTM D1737)


Flash point, °C


Taber abrasion, loss
CS 17 wheel
1kg,1000 rev
(ASTM D4060)



Application temperature

–35°C to 180°C

All values are subject to 5-10 % tolerance

Application Information
Instructions for use

Surface preparation

All surfaces must be dry, smooth, clean, sound, The surface of the substrate shall be sound, clean and uncontaminated.  
This preparation shall be such as to leave a sound expose surface free from dust, loose particles and any deleterious matter. If the surface is defective or has laitance, it must be cut back to a sound base.
New concrete or cementitious surfaces should be at least 28 days old and have moisture content not exceeding 5%. Old or existing surface should be refurbished mechanically to ensure clear and sound substrate.


Surface must be primed using UREAPRIME EP1. Once the primer has reached a tack-free status, the polyurea coating can be applied immediately.  Note that the entire primed surface must be coated within the day of application.


Use 1:1 ratio pump, with appropriate material heaters, as required for individual application. Please contact Colmef for further information.


ARMATUREA A1 must be spray applied using approved equipment. For application guidelines, please contact Colmef.


Clean equipment immediately after use. Cured product may be disposed of without restriction.  The un-cured isocyanate and resin portions should be disposed of according to local government regulations.

Additional Information
Health & Safety

All body parts should be covered and activated charcoal respirators or forced-air breathing apparatus are necessary for safe application of this product. Keep uncured product away from children at all times. All personnel should read and understand the safety recommendations stated in the Material Safety Data Sheet .

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updated on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
More Products from this section
Monneli Armaturea H1


Monneli Epomax

Epoxy Thixotropic Adhesive for Structural Gluing

EPOMAX is used for structure gluing in building industries such as:
Natural or artificial stones
Marble and granite
Rigid PVC
EPOMAX can be also used for the structural repairs of beams and pillars, steel plates gluing, filling large cracks in industrial floorings. It is also used in floors under heavy traffic or chemical aggression, and for repairing edges and rigid structural gluing of prefabricated concrete elements.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map