Industrial Flooring

Heavy Duty Industrial Flooring System

Monneli Epofinish IF

Solvent-Free Repair Mortar for Concrete Floors

EPOFINISH IF is used in various installations such as:
Commercial and residential car parking
Warehousing and storage facilities
Chemical and pharmaceutical factories
Food factories and slaughterhouses
back to Industrial Flooring
Technical Information
Product Description

EPOFINISH IF is a solvent free repair mortar for floors based on formulated epoxy resin, curing agents and silica sand specially selected for their ability to be applied and cured in cold temperatures.

Packaging, Coverage / Consumption


EPOFINISH IF is supplied as a pre-measured kit depending on the customer’s requirements. Our standard packing is 4 liter kit.

Shelf Life & Storage


Keep in tightly closed containers and in sheltered and dry place with a temperature between +5°C and +35°C. In these conditions it maintains its characteristics unchanged for 12 months.

Technical Properties


Solid content


Kit size

4 Liter

Theoretical coverage

4m² / 4 liter / 1 mm

Pot life at 18°C

90 minutes

Pot life at 30°C

40 minutes

Thin layer (3.2mm) Dry time at 20°C

15 hours 

Mixing ratio (by weight)
BASE     1.6
SAND   12
Mixed density at 20°C

2.02 kg/L

Application maximum relative humidity

75 %

Compressive strength (ASTM C579)

>  80.0 N / mm²

Bending strength (ASTM C580)

>  20.0 N / mm²

Tensile strength (ASTM C307)

>  14 N / mm²

Bond strength to concrete (ASTM D4541)

>  2.0 N / mm²

Taber abrasion (ASTM D4060 CS17 Wheels)

45 mg loss/1000cycles

Water absorption (ASTM D413 ) (maximum)


Porosity with no sealer NACE Sand TM-01-74


Hardness shore D


Application Information
Instructions for use

Surface preparation

For best finish and adhesion, apply over PRIMER POXY IF.

The concrete must be at least 21 days old.  The concrete must be free from loose matter, oil and dirt before starting surface preparation.

The EPOFINISH IF is also designed for deep and wide cracks. The cracks should be opened up by sandblasting or mechanical wire brushing. Undercut if necessary.


Items Needed

  • Multi-speed drill fitted with a mixing paddle
  • Hand held steel trowel
  • Clean bucket, 2” brush and SOLVENTE 10 to clean the equipment


Using a drill and a paddle at low speed, stir the resin (Component A) for 1 min.

Slowly add the hardener (Component B) and increase mixing speed. Mix for 1 minute, ensuring proper mixing between the resin and the hardener.

Slowly add the sand (Component C) and increase mixing speed. Mix for 2 minutes. Do not dump all the sand at once.
Pour the mix onto the floor immediately and spread using the steel trowel. Wet the blade with SOLVENTE 10 to aid application.


Clean equipment with SOLVENTE 10. In case of spillage, use fine silica or cement to absorb the spill and dispose of according to local regulations.


  • EPOFINISH IF contains resin (Component A), hardener (Component B) and Silica Sand (Component C):
  • EPOFINISH IF resin (Component A), is a low viscosity standard Coloured Base which contains fillers and pigments.
  • EPOFINISH IF hardener (Component B) is a low viscosity hardener which, after mixing with the resin can be applied in 95% humidity and on damp floors. The hardener provides excellent chemical and abrasion resistance.
  • EPOFINISH IF (Component C) is a graded low dusting silica sand.
Additional Information
Health & Safety

Study the MSDS of the product before use or storage.


EPOFINISH IF is not regulated per the “Directive 67/548/EEC EU Dangerous Materials List” so no special labeling is needed.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
More Products from this section
Monneli Epofloor E 250 (IF)

Solvent-Free Epoxy Topcoat for Concrete Floors

Monneli Epofloor SL (IF)

Solvent-Free Epoxy Self Leveling Topping (0.8 – 2.0mm) for Concrete Floors

Monneli Epofloor SL (IFT)

Solvent-Free Epoxy Self-Leveling Topping (2.0-4.0mm) for Concrete Floors

Monneli Neofil F10

Adhesive & Grout for Glass, Ceramic Marble Mosaics

NEOFIL F10 is used as adhesive, as well as, joint grout in the same application for interior and exterior floor and wall tiles including:
Ceramic, glass and marble mosaic on cementitious renders.
Mosaic on non planar substrates, without tiles slipping.
Mosaic on gypsum board panels.
NEOFIL F10 can be mixed with ELASTOKOL. When mixed is suitable for use:
Installing glass mosaic or ceramic tile on non absorbent surfaces
Installing glass mosaic or ceramic tiles in swimming pools, basins or similar structures even on absorbent substrates
Connected products
Monneli Solvente 10

Thinner / Cleaning Solvent

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map