Industrial Flooring

Heavy Duty Industrial Flooring System

Monneli Epofinish IF

Solvent-Free Repair Mortar for Concrete Floors

Uses
EPOFINISH IF is used in various installations such as:
Commercial and residential car parking
Workshops
Warehousing and storage facilities
Chemical and pharmaceutical factories
Food factories and slaughterhouses
back to Industrial Flooring
Technical Information
Product Description

EPOFINISH IF is a solvent free repair mortar for floors based on formulated epoxy resin, curing agents and silica sand specially selected for their ability to be applied and cured in cold temperatures.

Packaging, Coverage / Consumption

Packaging:

EPOFINISH IF is supplied as a pre-measured kit depending on the customer’s requirements. Our standard packing is 4 liter kit.

Shelf Life & Storage

Storage:

Keep in tightly closed containers and in sheltered and dry place with a temperature between +5°C and +35°C. In these conditions it maintains its characteristics unchanged for 12 months.

Technical Properties
PROPERTIES RESULTS
Solid content 100%
Kit size  4 Liter
Theoretical coverage  4m² / 4 liter / 1 mm 
Pot life at 18°C 90 minutes
Pot life at 30°C 40 minutes
Thin layer (3.2mm) Dry time at 20°C 15 hours 
Thin layer (3.2mm) Dry time at 40°C 5 hours 
Mixing ratio (by weight) 
Hardener 1
Base 1.6
Sand 12
Mixed density at 20°C 2.02 kg/L
Application maximum relative humidity 75%
Compressive strength (ASTM C579) >80.0 N / mm²
Bending strength (ASTM C580) >20.0 N / mm²
Tensile strength (ASTM C307) >14 N / mm²
Bond strength to concrete (ASTM D4541) >2.0 N / mm²
Taber abrasion (ASTM D4060 CS17 Wheels) 45 mg loss / 1000 cycles
Water absorption (ASTM D413 ) (maximum) 0.001%
Porosity with no sealer NACE Sand TM-01-74 0
Hardness shore D 85
All values are subject to 5-10% tolerance
Application Information
Instructions for use

Surface preparation

For best finish and adhesion, apply over PRIMER POXY IF.

The concrete must be at least 21 days old.  The concrete must be free from loose matter, oil and dirt before starting surface preparation.

The EPOFINISH IF is also designed for deep and wide cracks. The cracks should be opened up by sandblasting or mechanical wire brushing. Undercut if necessary.

Application

Items Needed

  • Multi-speed drill fitted with a mixing paddle
  • Hand held steel trowel
  • Clean bucket, 2” brush and SOLVENTE 10 to clean the equipment

Method

Using a drill and a paddle at low speed, stir the resin (Component A) for 1 min.

Slowly add the hardener (Component B) and increase mixing speed. Mix for 1 minute, ensuring proper mixing between the resin and the hardener.

Slowly add the sand (Component C) and increase mixing speed. Mix for 2 minutes. Do not dump all the sand at once.
Pour the mix onto the floor immediately and spread using the steel trowel. Wet the blade with SOLVENTE 10 to aid application.

Cleaning

Clean equipment with SOLVENTE 10. In case of spillage, use fine silica or cement to absorb the spill and dispose of according to local regulations.

Components

  • EPOFINISH IF contains resin (Component A), hardener (Component B) and Silica Sand (Component C).
  • EPOFINISH IF resin (Component A), is a low viscosity standard Coloured Base which contains fillers and pigments.
  • EPOFINISH IF hardener (Component B) is a low viscosity hardener which, after mixing with the resin can be applied in 95% humidity and on damp floors. The hardener provides excellent chemical and abrasion resistance.
  • EPOFINISH IF (Component C) is a graded low dusting silica sand.
Additional Information
Health & Safety

Study the MSDS of the product before use or storage.

 

EPOFINISH IF is not regulated per the “Directive 67/548/EEC EU Dangerous Materials List” so no special labeling is needed.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofloor E250 (IF)

Solvent-Free Epoxy Topcoat for Concrete Floors

Monneli Epofloor SL (IF)

Solvent-Free Epoxy Self Leveling Topping (0.8 – 2.0mm) for Concrete Floors

Monneli Epofloor SL (IFT)

Solvent-Free Epoxy Self-Leveling Topping (2.0-4.0mm) for Concrete Floors

RANDOM PRODUCT
Monneli Epofloor P500

Single Component Polyurethane UV Resistant Traffic Coating Low VOC

Uses
EPOFLOOR P500 is used in heavy duty traffic deck systems and is suitable for use in both internal and external applications.
Epofloor P500 may be used in the following application:
Car park decks (inside / outside)
Trafficable flat roofs
Traffic ramps
Plant rooms
Pedestrian walkway
Light engineering workshops
Connected products
Monneli Solvente 10

Thinner / Cleaning Solvent

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map