Industrial Flooring

Polyurethane Based Flooring Systems

Monneli Epofloor P1200

Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System

Uses
EPOFLOOR P1200 is recommended for floors that require durable abrasion-resistant finish such as:
Car park decks
Ramps
Loading bay areas
Production & assembly halls
Hospitals
Schools
Warehouses
Service corridors
Aircraft hangars
back to Industrial Flooring
Technical Information
Product Description

EPOFLOOR P1200 is a multi-layer, UV resistant, flexible Polyurethane based system for the protection of concrete floors subject to high levels of traffic, impact and abrasion.

Advantages

n Seamless and water tight

n Durable, low maintenance

n High mechanical strength and abrasion resistance

n Flexible system which reduces the risk of cracking

n Good chemical resistance for mild acid and alkali

Packaging, Coverage / Consumption

 

  Packaging    
  PRIMER PU    15 liter kit
  EPOFLOOR P360      15 liter kit
  EPOFLOOR P440    15 liter kit
  QUARTZO No. 2    25 kg bag
  SOLVENTE 10    20 liter pail

 

Consumption
PRIMER PU     6-8m²/Liter depending on surface texture and porosity of the surface
EPOFLOOR P360   2.5-4kg/ m²
EPOFLOOR P440    0.10-0.12 kg/ m² / coat
QUARTZO No. 2   15kg / unit of EPOFLOOR P360

 

System Thickness

 From 1.5 mm – 2.5 mm

Shelf Life & Storage

Storage:

Store the product in dry closed place with temperature between +10ºC to +35ºC. Storage above this temperature may reduce shelf life. In closed containers and in dry environment.

Colors
Primer PU - Amber Epofloor P 360 - Grey, Light grey, Red, Green, Blue (further colors are available on request)
Technical Properties
PROPERTIES RESULTS
Appearance  Clear liquid coating
Color  Amber
Density at 25°C  0.95 kg/L 
Adhesion strength Greater than cohesive strength of typical good quality concrete substrate
Recoating interval at 25°C 8 – 12 hours
EPOFLOOR P360 
Appearance Liquid coating
Color Grey, light grey, red, green, blue (further colors are available on request)
Density at 25°C 1.45 kg/L
VOC 12.0 g/L
Solid content 100%
Viscosity at 25°C, 50 s-1 8,000 cps
Elongation (ASTM D412) Up to 40%
Tensile strength (ASTM D412) 25 N/mm2
Tear strength (ASTM D 624) > 40 N/mm2
Compressive strength (ASTM C 579) 50 N/mm2
Adhesion strength > 2.5 N/mm2
Shore D hardness 75
Full cure 7 days
Re-coating interval 12 – 24 hours
Working time >30 minutes
Permissible ambient and substrate temperature +8°C - 30°C
Maximum permissible RH 75%
EPOFLOOR P440 
Appearance Liquid coating
Color Refer to Colmef Color Chart
Density at 25°C 1.25 kg/L
All values are subject to 5-10% tolerance
Application Information
Instructions for use

 

  EPOFLOOR P1200 SYSTEM COMPONENTS
  PRIMER PU   Solvent based epoxy primer
  EPOFLOOR P360   Two component self levelling solvent free tough floor coating
  EPOFLOOR P440   Two component aliphatic PU tough coat
  QUARTZO No. 2   Graded aggregate (0.3 – 0.9 mm)

Surface preparation

The surface should be sound, clean, dry and free from loose and flaking materials, efflorescence, laitance, curing compounds, dirt, oil, grease or other contaminants. Mechanical methods like grinding or grit/captive blasting in order to provide a suitable profiled open textured surface is strongly recommended.

New concrete or cementitious surfaces should be at least 28 days old and have moisture content not exceeding 5%. Old or existing floor should be refurbished mechanically to ensure clear sound substrate.

Surface irregularities and blow holes shall be repaired with EPOFINISH C, a solvent free epoxy resin repair mortar. Allow the repair material to harden.

Expansion joints shall be repaired using EPOMORT HS, a high strength solvent free epoxy mortar.

After all preparation is complete, ensure dust is removed from the surface using an industrial vacuum.

Application

Priming

Apply PRIMER PU, a high performance Polyurethane primer using a suitable roller at the rate of 5-6m²/Liter depending on the substrate profile and porosity.

The primer should be left to achieve a tack-free condition for 6 – 8 hours before applying the top coat. If the substrate is excessively porous, a second coat of primer shall be applied again.

Intermediate Coat (Smooth Finish)

Mix components A and B of EPOFLOOR P360 together adding 15 kg QUARTZO NO. 2 whilst mixing for a minimum of 2 minutes, using a slow speed electric mixer at 300-400 rpm. Work the mixed products round the mixing pail to ensure it scrapes the side and bottom of the pail.

Pour the material onto the primed surface in pools or as a long strip at a consumption rate of 2.5-4kg/ m2. Spread the mixture on the floor with the use of trowel, pin screed or notched trowel.

Roll the material within 5 minutes after it is leveled in order to release trapped air using a spike roller. Allow to cure for 12 hours at 25°C before allowing light traffic.

Top Coat

To provide a UV resistant coating to the system and to enhance durability performance, apply one coat of EPOFLOOR P440 at a rate of 0.10-0.12 kg/ m2 per coat.

Intermediate Coat (Rough Finish, Anti-Slip)

Apply EPOFLOOR P360 mixed product on the primed surface at a rate of 2.5-3kg/ m2 . Once the product is leveled, broadcast QUARTZO NO. 2 at a rate of 2 to 3 kg/m2.

Allow the applied product to cure (minimum 5 hours), then remove the excess sand. Remove the prominent particle using a trowel then clean the substrate with a vacuum. Apply one more coat of EPOFLOOR P360 at a rate of 2.5-4kg/ m2.

Top Coat

To provide a UV resistant coating to the system and to enhance durability performance, apply one coat of EPOFLOOR P440 at a rate of 0.10-0.12 kg/ m2.

Recommendations

n EPOFLOOR P1200 should be applied to the prepared floor after a curing of 28 days or more has elapsed.

n EPOFLOOR P1200 should not be applied to the following substrates: damp substrates, asphalt, PVC tiles or sheets, hardboard / chipboard.

n Do not apply EPOFLOOR P1200 when the humidity exceeds 90%.

n Make sure that the substrate temperature is 3°C higher than the dew point.

Cleaning

Clean tools with SOLVENTE 10 promptly before material hardens. Cured material must be mechanically removed.

Additional Information
Health & Safety

Avoid contact with skin & eyes. Protective clothing such as gloves & safety goggles should be worn during application. Treat any splashes to the skin or eyes with fresh water immediately.

 

Should the product be accidentally swallowed, do not induce vomiting, but call for medical assistance immediately. Ensure adequate ventilation at site and avoid inhalation of vapours.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.34Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofloor P1100

Seamless, Flexible, Polyurethane Flooring System

Monneli Epofloor P1140

Seamless, Polyurethane Traffic Deck Coating System

Monneli Epofloor P1150

Protective, Polyurethane Based Traffic Deck Coating System

Monneli Epofloor P1160

Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System

Monneli Epofloor P125

POLYURETHANE COATING FOR CONCRETE FLOORS

view more
RANDOM PRODUCT
Monneli Armonite

BENTONITE

Uses
ARMONITE is suitable to be used in various fields of civil engineering applications where it is required to obtain activatation of bentonite.
ARMONITE is added to the mix mainly used in the following:
Slurry to be used in tunneling
Micro tunneling and pipe jacking
Injections and consolidation grouting
Backfilling mixes in order to fill the gaps between segments liner and soil excavation
Drilling fluid able to sustain the excavation vertical walls
Other uses:
Well drilling mud
Sealing agent
Asphalt concrete mixtures
Casting, foundry sand
Other engineering projects
Connected products
Monneli Epofinish C

Fairing Coat Solvent Free Epoxy Mortar

Monneli Epomort HS

High Performance Epoxy Mortar

Monneli Solvente 10

Thinner / Cleaning Solvent

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map