Protective Coating

Epoxy Based Coating

Monneli Epossitar 100

High Build Solvent Free Coal Tar Epoxy Coating

Uses
EPOSSITAR 100 is used as follows:
As an anti-corrosive coating, suitable for industrial atmosphere, immersion in salty and alkaline solutions, crude oil, for concrete sewerage pipes, and manholes
As a tank lining in crude oil and water ballast tanks, coffer dams etc.
To provide chemical corrosion and abrasion resistance to concrete surfaces for many application including seawater tanks, manholes, lining, channels, sewage plants, etc.
As an outstanding protective coating on permanently submerged surfaces such as ship hulls, sheet piling, concrete, sewerage pipes, off shore structures, foundation walls & slumps
back to Protective Coating
Technical Information
Product Description

A two component solvent free epoxy polyamide coating, modified with low temperature tar. It is specially formulated for high build applications. Once cured, it produces a tough, flexible, chemical and impact resistant film.

 

Formulated to be easily applied, as thick as 200 microns in one coat. It provides very good resistance to aggressive chemicals, water, acids, and alkalis.

Advantages
  • Self-priming
  • Excellent anticorrosive ability
  • 100% solid content
  • High build
  • Low temperature curing
  • Heavy duty structural coating
  • Easily applied by roller, brush or spray
  • Exceptional resistance to impact, thermal shock & abrasion
Packaging, Coverage / Consumption

Packaging:

EPOSSITAR 100 is supplied as 20 Liter Kit and 400 kg Kit.

 

Consumption: 

Approximately 5m²/Liter at 200 microns.

Shelf Life & Storage

Storage:

Store generally in dry covered place with a temperature between +5ºC- +35ºC and RH below 70%. The expected shelf life of the product is 12 months from production date.

Colors
Black
Technical Properties
PROPERTIES RESULTS
Colour  Black
Mix density at 25⁰C  1.35 kg/L 
Solid content  100% 
Pot life at 25⁰C >1 hour
Recommended film thickness (DFT) 200 – 400 microns
Compressive strength (ASTM C 579) >40 N/mm²
Elongation (ASTM D638-10) 30%
Tensile strength (ASTM D638-10) >5 N/mm²
Water permeability (24 hrs) at 5 bars pressure (BS 12390) Nil
Abrasion resistance (ASTM C501-84) 0.24gm / 1000 cycles
Thermal coefficient of expansion (ASTM C531) 7.3 x 10-5°C-1
Drying at 100 mic. (250C, 65%) RH Touch dry  After 4 hours
Pull-out strength  (ASTM D4541-09) >2.0 N / mm²
Water absorption (ASTM D 570-98) <0.01%
Mixing ratio (by volume) 
Base 1
Hardener 1
Minimum recoating time at 25°C 8 hours
Cured at 25°C 7 days
Temperature of application +5⁰C to +35⁰C
Service temperature -5⁰C to +80⁰C
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface preparation

All surfaces must be dry, smooth, clean, sound, uncontaminated, and free from dust or loose material. Concrete surfaces must be fully cured and laitance must be removed by any suitable method.

For old concrete, all contamination must be removed and a sound clean substrate should be exposed. Mechanical means of preparation are preferred followed by the removal of dust and other loose debris using an industrial vacuum.

Cracks should be reinforced with fibre mesh and must then be treated with epoxy mortar. Contact Colmef Technical Department for recommended products.

Mixing

Prior to application, stir component A (resin), then add component B (hardener) to it and mix thoroughly with a low speed electric drill (200 – 300 rpm) fitted with a suitable paddle to obtain a homogenous mixture.

Application

After mixing, the product is ready for brush or airless spray application 5-10% SOLVENTE 10 may be added for airless spray application. 5-10% SOLVENTE 10 may be added for airless spray application. Use nozzles of 0.21 - 0.025 and working pressure of 140 - 160 bar, for brush or roller add 5% volume SOLVENTE 10 only if needed.

EPOSSITAR 100 is generally applied as a two coats application with a wet thickness of 200-300 microns per coat. The hardening time vary sensitively according to environmental conditions and the type of support.

Cleaning

Tools and equipment should be cleaned with SOLVENTE 10 immediately after use. Hardened material should be removed mechanically. Spillages should be absorbed with sand or sawdust and disposed of in accordance with local regulations.

Recommendations

  • EPOSSITAR 100 should not be applied over existing coatings.
  • For application in hot weather, it is strongly recommend to shade the working area and to keep the equipment used cool.
  • Application should not be undertaken if the temperature is below +5⁰C, nor when the revailing relative humidity exceeds 90%.
  • The colour of the coated surface will change to dark brown if cured in a high humidity environment.
  • Cannot be overcoated after 24 hours.
Additional Information
Health & Safety

Keep the product away from sources of ignition.

 

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment. Avoid contact with skin, eyes and inhalation of vapour. Ensure proper ventilation at working place.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epochim EPS

Epoxy Polysulphide Elastomeric Coating

Monneli Epochim K100

High Chemical Resistant Epoxy Coating

Monneli Epochim K40

Water Based Epoxy Coating for Non-Toxic Applications

Monneli Epossitar 100 CR

High Build Solvent Free Coal Tar Epoxy Coating

Monneli Epossitar 70

Coal Tar Epoxy Coating

RANDOM PRODUCT
Monneli Neofil Poxy

High Performance Epoxy Grout for Tiles

Uses
NEOFIL POXY is used for internal and external tile grouting for ceramic tiles, mosaic, natural stones (every type of marble especially those sensitive to water such as verde alpi, rosso sicilia, sandstones, slate), klinker, etc.
NEOFIL POXY can be used as a tile grout wherever excellent mechanical properties, chemical resistance, and hygienic environment is required. This includes chemical factories, food production and processing, catering facilities, electrical and mechanical rooms, service facilities, laboratories, etc.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map