Tile Grouts

Cement Based Tile Grouts

Monneli Giuntolastic

Synthetic Latex Additive for Cementitious Grout

Uses
GIUNTOLASTIC is used for mixing, fully or as partial substitute of water with NEOFIL COLOR and FUGACOLOR grout for tile grouting in the following applications.
Swimming pool, fountains, steam rooms, refrigerating room
External applications
Floors exposed to heavy pedestrian traffic
Floors and walls exposed to vibration, high temperature variation, deflection
For grouting joints between high absorbent tiles
For areas where high abrasion, water and chemical resistance is required
back to Tile Grouts
Technical Information
Product Description

GIUNTOLASTIC is an extremely elastic water based polymer. It is designed to be mixed with cementitious grout (NEOFIL COLOR or FUGACOLOR) in total or in partial replacement to water. The mixture of GIUNTOLASTIC with tile grout powder improves the compactness, abrasion resistance, impermeability and adhesion of grout when applied in joints between tiles.

In addition, the elastic property of the product allows the grout to absorb certain deformation and vibration on the substrates.

Advantages
  • Improve adhesion to substrates
  • Improve deformability and impermeability of the grout after complete curing
Compiliance Standard
  • European EN 13888-CG2
  • ANSI A 118.6 -1999
Packaging, Coverage / Consumption

Packaging:

GIUNTOLASTIC is available in 20 Liter plastic pails.

 

Consumption: 

Please refer to NEOFIL COLOR and FUGACOLOR data sheets.

Shelf Life & Storage

Storage:

Store in dry and covered place out of direct sunlight and protect from high temperature (higher than +35ºC).

 

Shelf life:

12 months if stored as recommended.

Technical Properties
PROPERTIES

RESULTS

Appearance

White liquid

Density at 25⁰C

1.02 kg/L

VOC

1.0g/L

Pot life time at 25⁰C

60 minutes

Mixture’s ratio with NEOFIL COLOR 0-4

30 : 100

Mixture’s ratio with NEOFIL COLOR 4-20

25 : 100

Mixture’s ratio with FUGACOLOR

30 : 100

Harmfulness ECC 88/379

No

Temperature of application

+5⁰C to 35⁰C

pH

7 – 8

All values are subject to 5-10 % tolerance

Application Information
Instructions for use

Surface preparation

The joints between tiles should be clean free of dust. Clean the joints between tiles and brush before grouting.

Mixing

Shake GIUNTOLASTIC pail before use. Pour a part of the latex as needed into a clean container and then add NEOFIL COLOR 0-4, NEOFIL COLOR 4-20 or FUGACOLOR. Mix to get a homogeneous paste free from lumps.

Application

Leave the mixture for about 10 minutes, then remix shortly and apply with a rubber grout float into the previously cleaned and wet joints.

Let the product set for about 20 minutes, and then proceed with cleaning the tiles with soft sponge. After the complete hardening of the grout, remove, with a dry sponge, all the remaining traces of grout on the surface. If the surface is still dirty clean it with PULINET. Read the instruction of PULINET in the technical data sheet before application.

Cleaning

Tools and equipment should be cleaned with water immediately after use.

NEOFIL COLOR mixed with GIUNTOLASTIC would perform as follows:

   Properties Result
(0–4 mm)
Result
(4–20 mm)
  Density of the mix (kg./Lt.) 1.80 1.90
  Flexural strength (N/mm²) 7 7
  Compressive strength (N/mm²) 30 30
  Water absorption (after 30 minutes) < 5 g < 5 g
  Shrinkage (mm/m) < 3 < 3
  Temperature resistance -30 to +80⁰C -30 to +80⁰C

 

Additional Information
Health & Safety

Handle the product with caution.

 

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
OTHER PRODUCTS
More Products from this section
Monneli Fugacolor

Water Repellant Anti-Fungus Tile Grout

Monneli Neofil Color 0-4 mm

Latex Modified Cementitious Tile Grout for Joints 0-4 mm Wide

Monneli Neofil Color 4-20 mm

Latex Modified Cementitious Tile Grout for Joints 4-20 mm Wide

Monneli Neofil Grout Thick

Latex Modified Cementitious Tile Grout for Joints 4-20 mm Wide

Monneli Neofil Tile Grout

Latex Modified Cementitious Tile Grout for Joints 0-4 mm Wide

view more
RANDOM PRODUCT
Monneli Elastoseal PS

Two Component Polysulphide Sealant

Uses
Elastoseal PS is used as:
Expansion joints for: Bridges, roadways, warehouse floors, airport runways and apron pavements
Sealing of moving and construction joints as well as joints between different construction materials in high rise buildings, roof terraces & ceilings, structural expansion joints running through the ceiling
Sealing of joints in water retaining structures such as reservoirs, dams, canals and culverts
Vehicular and pedestrian traffic pavements of concrete
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map