Waterproofing

Bitumen Waterproofing

Monneli Asfabit RBL

RUBBERIZED BITUMEN EMULSION

Uses
ASFABIT RBL can be used as follows:
Provides a sandwich membrane between screed flooring
A waterproofing coat for concrete foundations, bricks, retaining walls, etc.
It can be used to waterproof walls and floors in wet areas
For maintenance of many types of roofs including built up felt, aluminum, concrete, lightweight screed, timber, slate, asbestos, bitumen sheets, etc.
As a vapour/salt barrier for exterior walls to building facades behind granite, marble, stone, cladding, curtain walls, etc.
Can be used as adhesive for insulation boards and expanded polystyrene
As curing compound for freshly cast concrete
back to Waterproofing
Technical Information
Product Description

ASFABIT RBL is a cold applied rubberized bitumen emulsion in dark brown color that, when dries, it forms tough black seamless and flexible coating.

Advantages
  • Economical
  • Water based with excellent adhesion
  • Nonflammable
  • Easily applied by brush or squeegee.
  • Excellent resistant to alkalis, mild acids, chlorine
  • Compatible with all bituminous products
  • Resistant to chlorides and sulfates
Compiliance Standard
  • ASTM D 1187, D 2939
  • BS 8102
  • ASTM D 1227, Type III Class 1 & 2
Packaging, Coverage / Consumption

Consumption

2 to 4 m² / liter

 

Packaging

ASFABIT RBL is packed in 20 and 200 Liter Drums

Shelf Life & Storage

Storage

Should be stored under cover away from extreme heat or direct sunlight or frost.

 

Shelf Life

12 months in tightly sealed containers if stored properly.

Technical Properties
PROPERTIES RESULTS
Appearance  Dark brown dries to seamless black coating
Density at 25°C  1.0 kg/L 
VOC 30.0 g/L 
Solid content  35% ± 2 
Rubber content 10% in the dried film 
Water resistance Good
Chloride resistance Excellent
Flash point Non-flammable
Application temperature +5°C to +45°C
Service temperature –5°C to +80°C
All values are subject to 5-10% tolerance
Application Information
Instructions for use

Surface preparation

The surface of the concrete shall be sound, clean and uncontaminated. 

This preparation shall be such as to leave a sound exposed concrete surface free from dust, loose particles and any deleterious matter. If the concrete surface is defective or has laitance, it must be cut back to a sound base.

Moss and lichen must be removed physically followed by treatment with fungicidal wash. After treatment, it must be washed down thoroughly with clean water and allow to dry.

Priming

Hot, very dry or porous surfaces should be primed before applying ASFABIT RBL.

 Mixing

ASFABIT RBL should be stirred before use until a uniform color and consistency is achieved. Product is ready for use.

Application

For waterproofing underground structures, the bituminous emulsion shall be applied by brush or roller depending on the dry film thickness required 400 micron dry film thickness (DFT) can be achieved when applied at 1m² /Lt/coat. The two coats must be applied at right angles to one another with a minimum of 6hours intervals between each application on at 35°C. Ensure that coat is completely dry before the next coat is applied.

Cleaning

ASFABIT RBL products should be removed from tools, equipment and mixers with clean water prior to the initial set. Cured material can only be removed mechanically.

Recommendation

  • Do not apply subsequent applications if the membrane is punctured or damaged.
Additional Information
Health & Safety

ASFABIT RBL is non-flammable, non-hazardous product. However, proper measures should be taken during work to avoid contact with eyes or skin. In the event of contact with eyes, wash immediately with clean water and seek medical care.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.25Mb)
OTHER PRODUCTS
More Products from this section
Monneli Asfabit

Cold Applied Bitumen Emulsion

Monneli Asfabit EM

Emulsified Thixotropic Flexible Protective Barrier to Vapor Transmission

Monneli Asfabit Prime

Quality Black Bitumen Primer

Monneli Asfabit RB

Flexible, Rubberized Bitumen Emulsion

Monneli Asfabit RB+

FLEXIBLE, RUBBERIZED BITUMEN EMULSION

view more
RANDOM PRODUCT
Monneli Betocure S

Water based concrete curing compound

Uses
BETOCURE S is used as an effective and economical curing agent compared to the traditional Hessian, water and polyethylene curing system. Suitable for all types of concrete surfaces such as:
Interior and Exterior Floor Slabs
Sidewalks
Driveways
Beams and columns
Warehouse flooring
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map