Grouting & Anchoring

Epoxy Based Grouts

Monneli Epogrout GP

General Purpose Flowable Epoxy Grout

Uses
EPOGROUT GP is used in the following:
Heavy machinery, equipment or structural elements needing maximum bearing support
Large or wide plates requiring precision grouting
Pile cap waterproofing sealing
High vast lighting bases
Narrow clearance situations including anchor bolts
Pile cap head treatment and waterproofing
Equipment bases where chemical and acid spillage occur
back to Grouting & Anchoring
Technical Information
Product Description

Three components solvent based epoxy grout consisting of base (A), hardener (B) and graded filler (C). When mixed together, the product becomes self leveling, free flow grout. It is designed for grouting of gap widths of 10-50mm.

Should be used in situation where heavy dynamic loads exist, high bearing and mechanical strengths are required, or high chemical resistance is needed.

Advantages
  • Excellent performance under dynamic or mobile loads
  • Non-shrinking with high adhesion to contact surfaces
  • High compressive, tensile and flexural strengths which give very good durability
  • High chemical resistance
  • Low creep characteristics under strained loading
  • High early strength gain
  • Excellent adhesion to steel and concrete
  • Excellent fatigue resistance
  • High resistance to dynamic loads, thermal effects and chemical attacks
Packaging, Coverage / Consumption

n Packaging:

The product supplied in a three-component 30kg kit.

 

n Consumption: 

Approximately 15L per 30kg kit.

Shelf Life & Storage

n Storage:

Keep the product in dry, covered conditions at 25ºC. In these conditions, product stability is 12 months from date of manufacturing.

Colors
Grey
Technical Properties
PROPERTIES RESULTS
Color Grey
Density at 25⁰C  2.0 kg/L 
VOC 4.2g/L 
Pot life at 25ºC 75 minutes
Compressive strength (ASTM C579) 
at 7 days 80 N / mm²
Flexural strength at 7 days (ASTM C580)  20 N / mm²
Tensile strength at 7 days (ASTM C307) 10 N / mm²
Chemical resistance Oil, mild acid and alkalis, water, grease and most chemicals
Abrasion resistance Higher than concrete
Impact strength Higher than concrete
Maximum flow (100mm head) 
with 35 mm gap 1000 mm
with 70mm gap 1800 mm
Water penetration Nil
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface Preparation

Concrete must be cured for a minimum of 21 days. All surfaces must be clean, sound, uncontaminated, free from oil, grease, water, paints and dust. Unsound concrete must be removed. Compressive strength of the concrete should not be less than 25 Mpa.

Concrete surface must be totally dry when the mixed product is poured as wet surface might cause debonding between concrete and the grout.

Steel surfaces should be free of rust. Sand blasting or grinding is recommended.

Formwork, if needed, must be well braced, leak proof, strong and will fixed as EPOGROUT GP product is free flowing grout.

Anchor bolt holes should be clean of all dust, dirt and should be dry.

Priming

Cleaned steel surface should be protected using PRIMER POXY FF only when there is a long delay in pouring the mix to avoid a chance of rusting of the surface.

Mixing

EPOGROUT GP is supplied in a pre-measured packing. Partial mixing should not be allowed under any condition.

Start mixing by pouring hardener B into base A, the two components must be well mixed to ensure proper chemical reaction.

Use a slow speed drill fitted with suitable paddle to mix the product at low number of turns (200 – 300 rpm).

Mix for few minutes till a homogeneous mixture is obtained, then add component C (filler/aggregate) and mix for 2 – 3 minutes until you get a uniform color mixture.

Application

Start pouring the grout from one side to eliminate air entrapment, the placement of the grout must be continuous. EPOGROUT GP should be used immediately after mixing the components and during the working time of the mix.

Cleaning

All used tools should be cleaned with SOLVENTE 10 before the product cures. Hardened material should be removed mechanically.

Recommendations

n Do not apply EPOGROUT GP if the temperature is less than 5⁰C.

n Partial mixing of the product components should not be allowed under any conditions.

n Extra care should be taken when applying at high temperature as pot life of the mixed product will shorten automatically.

n It is recommended to shade the working area while mixing and placing EPOGROUT GP.

Additional Information
Health & Safety

Wear protective gloves and goggles during application. This product contains chemicals which may be potentially harmful to your health if not used properly. It is strongly recommended to read the material safety data sheets for proper storage and to observe precautions.

 

If contact with skin or eyes happen, use resin cream to remove it from skin followed by clean water, do not use solvent. In case of contact with eyes, use clean water and seek medical consultation.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.25Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epogrout GP Flex

FLEXIBLE HIGH PERFORMANCE FLUID URETHANE EPOXY GROUT

Monneli Epogrout PC

High Strength Epoxy Mortar for Pile Treatment

Monneli Epogrout PC Extra

Flowable Epoxy Grout for Pile Treatment

RANDOM PRODUCT
Monneli Asfabit RB+

FLEXIBLE, RUBBERIZED BITUMEN EMULSION

Uses
ASFABIT RB+ can be used as follows:
To provides a sandwich membrane between screed flooring
A waterproofing coat for concrete foundations, bricks, retaining walls, etc.
It can be used to waterproof walls and floors in wet areas
For maintenance of many types of roofs including built up felt, aluminum, concrete, lightweight screed, timber, slate, asbestos, bitumen sheets, etc.
As a vapor/salt barrier for exterior walls to building facades behind granite, marble, stone, cladding, curtain walls, etc.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map