Industrial Flooring

Primers

Monneli Primer Poxy FF

Solvent Free High Performance Epoxy Primer

Uses
PRIMER POXY FF can be used as follows:
PRIMER POXY FF is used as an adhesion coat on supports like concrete, ceramics, plastic, before other protective or waterproofing coatings, such as, epoxy or polyurethane applications.
When diluted with 20% SOLVENTE10, it can be applied on porous and absorbent surfaces to improve the surface strength.
Sealing of highly porous cementitious substrate.
back to Industrial Flooring
Technical Information
Product Description

Two components solvent free low viscosity epoxy primer. It has an outstanding adhesive bond between the substrate and the epoxy or polyurethane floor coating.

Adheres to a variety of substrate and can be applied as scratch coat with the addition of graduated sand.

Advantages
  • Good penetration to substrate
  • Excellent mechanical properties
  • Excellent water resistance
  • Excellent adhesion to concrete, timber, granolithic screeds, masonry paving ... etc.
  • Designed for highly porous surfaces
  • High wetting properties
  • Damp tolerant
  • Perfect for use with epoxy, urethane screeds and self smoothening toppings
Packaging, Coverage / Consumption

Packaging:

PRIMER POXY FF is available in 4 and 15 Liter packing

 

Consumption:

4-5 m² / liter per coat according to the porosity of the support.

Shelf Life & Storage

Storage:

Store the product in dry closed place with temperature between +5°C and +35°C. In these conditions, the product maintains its stability for 12 months.

Technical Properties
PROPERTIES RESULTS
Appearance Liquid
Color Clear to reddish
Mix density at 25°C  1.05  kg /L 
VOC 13.0 g/L
Viscosity at 25°C 800 - 1000 cps
Pot-life time at 25°C 60 minutes
Drying time at 25°C 4 hours
Re-coatable after 6 hours at 40°C
  12 hours at 20°C
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface preparation

All surfaces should be sound, clean, dry and free from loose and flaking material, efflorescence, laitance, curing compounds, dirt, oil and grease.

New concrete or cementitious surfaces should be allowed to cure and have moisture content not exceeding 5%. Old or existing floor should be refurbished mechanically to ensure clear sound substrate.

Surface irregularities and blow holes shall be repaired with EPOFINISH C, a solvent free epoxy resin repair mortar.  Allow the applied material to  harden. After all preparation is complete, ensure dust is removed from the surface using an industrial vacuum.

Expansion joints shall be repaired using EPOMORT HS,   a high strength solvent free epoxy mortar.

Mixing

For preparation of product, pour component B (hardener) into component A (resin) and mix carefully with electric mixer at low number of turns, till obtaining a homogeneous mix. It is always recommended to mix a complete kit at a time.

Application

Apply the product with a brush or roller or squeegee in its pure state at a rate of 4-5m2/Liter per coat. This rate might vary depending on surface conditions. The primer must be well scrubbed into the substrate to ensure full coverage. Allow the primer to cure (6-8 hrs) before applying subsequent coats. If the primed surface is not overcoated within 24 hours, a fresh coat of primer has to be applied again.

Cleaning

Clean tools with SOLVENTE 10 promptly before material hardens. Cured material must be mechanically removed.

Recommendations

n Don’t apply the product with imminent rain forecast

n PRIMER POXY FF should not be applied on asphalt floor and PVC tiles

n PRIMER POXY FF should not be applied on the concrete surface that has greater than 4% maximum moisture content

Additional Information
Health & Safety

Avoid contact with skin & eyes. Protective clothing such as gloves & safety goggles should be worn during application. Treat any splashes to the skin or eyes with fresh water immediately. Should the product be accidentally swallowed, do not induce vomiting, but call for medical assistance immediately. Ensure adequate ventilation at site and avoid inhalation of vapors.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Primer Poxy

Solvent Based Epoxy Primer

Monneli Primer Poxy (FC)

Fast Cure Solvent-Free Epoxy Primer for Concrete Floors

Monneli Primer Poxy (IF)

Penetrating Solvent-Free Epoxy Primer for Concrete Floors

Monneli Primer Poxy FF*

Solvent Free Epoxy Primer

Monneli Primer Poxy WB

Water Based Epoxy Primer

view more
RANDOM PRODUCT
Monneli Primer Poxy WB

Water Based Epoxy Primer

Uses
PRIMER POXY WB is recommended for use in commercial, institutional, or industrial environments that require a low odor, fast drying, and durable coating.
It can be used over prepared substrates such as steel, aluminum, and concrete in industrial environments and as part of a system to be top coated with epoxy or acrylic coatings as anti-dust treatment of industrial flooring.
PRIMER POXY WB is used as a primer on the following substrates prior to the application of Epoxy or Polyurethane coatings:
Concrete surfaces
Steel and aluminum
Refineries
Zinc-rich coatings
Manufacturing equipment
Pipe racks
Structural steel
Power plant
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map