SELF SMOOTHENING EPOXY BASED FLOOR TOPPING FROM 3mm to 5mm THICKNESS
A multi component high performance self smoothening epoxy flooring system that flows in a light oil like manner to self smoothen to a perfect level. Once cured, the product has excellent abrasion and chemical resistance .
EPOFLOOR SLE40 provides an attractive hard wearing and easily cleanable floor finish. Its use on floors will enhance lighting in the environment due to the product’s reflective properties.
Packaging
The product supplied in 15 liter kit
Consumption:
1.0m²/Liter per 1 mm thickness depending on substrate condition
Storage
Keep the product in dry and sheltered place, at the temperature between +50C and 350C.
Shelf Life
At least 12 months if stored as recommended.
|
Substrate preparation
Concrete Substrates
The surface of the concrete to be prepared shall be sound, clean and uncontaminated.
This preparation shall be such as to leave a sound exposed concrete surface free from dust, loose particles and any deleterious matter. If the concrete surface is defective or has laitance, it must be cut back to a sound base. Excess laitance deposits are best removed by light mechanical scrabbling, grinding or grit/captive blasting followed by vacuum cleaning to remove dust debris.
Any blowholes, chipping or similar surface imperfections shall be repaired using EPOFINISH C, a solvent free epoxy resin repair mortar. Allow the repair material to harden.
Expansion joints shall be repaired using EPOMORT HS, a High strength solvent free epoxy mortar.
New concrete or cementitious surfaces should be allowed to cure and have moisture content not exceeding 5%. Old or existing floor should be refurbished mechanically to ensure clear sound substrate.
Priming
All surfaces treated with EPOFLOOR SLE40 should be primed with PRIMER POXY FF, a solvent-free high performance epoxy primer.
Add the content of Hardener can (Part B) into the Base can (Part A) and mix for two minutes until a homogenous mixture is achieved.
Apply one coat of PRIMER POXY FF onto the dry surface, maintaining the consumption of 150 - 300 g/m² and observing the application intervals indicated in the relative technical data sheet.
Allow primer to dry before proceeding with the self levelling application. Do not apply EPOFLOOR SLE40 while the primer is tacky as this will lead to unsightly marks in the finished surface. Highly porous substrates may require a second primer coat.
Mixing
EPOFLOOR SLE40 is supplied in three pre-weighed packs (Component A – Base, Component B – Hardener and Component C- Selected Silica) which are ready for immediate in-situ use.
Pour the hardener (Component B) into the base can (Component A) and and mix with low speed drill and paddle (200 – 300 rpm) for 2 – 3 minutes till obtaining a mix with uniform consistency before adding the selected silica (Component C). Scrape the sides and bottom of the can during mixing to ensure that a homogenous mixture is achieved before application.
Application
Pour the mixed material onto the primed surface in pools or as a long strip. Using a trowel, pin screed, or notched trowel, spread EPOFLOOR SLE40 to the required thickness. To release entrapped air and assist with the smoothing operation, roll the material within 5 minutes after it is leveled, using spiked roller.
Allow to cure for minimum 18 hours at +25°C for light traffic.
Cleaning
Tools and equipment should be cleaned with SOLVENTE 10 immediately after use. Hardened materials should be removed mechanically.
Spillages should be absorbed with sand or sawdust and disposed of in accordance with local regulations.
Recommendations
n EPOFLOOR SLE40 should not be applied at temperatures below +5°C and above +35°C
n EPOFLOOR SLE40 should not be applied to asphalt, weak or friable concrete, PVC tiles or sheet substrates
n EPOFLOOR SLE40 should not be applied if the surface relative humidity is more than 75%
n All existing expansion or movement joints should be followed through the new floor surface.
n It is strongly recommended to apply EPOFLOOR SLE40 by specialist contractor or experienced applicator who must follow the procedures laid down in the product method statements
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary. In case of contact with skin, rinse with plenty of water and seek medical advice accordingly.
If ingested, obtain medical attention immediately. Do not induce vomiting.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Epoxy Floor Coating
High Build Solvent Free Epoxy Flooring System
SOLVENT FREE, HIGH BUILD EPOXY FLOORING SYSTEM
High Performance Epoxy Floor Coating
Heavy Duty, Anti-Skid Surface Dressing
Two Components Elastomeric Polyurethane Waterproofing Coating
Fairing Coat Solvent Free Epoxy Mortar
High Performance Epoxy Mortar
Solvent Free High Performance Epoxy Primer