Industrial Flooring

Line Marking Coating

Monneli Epofloor LM

Line Marking Coating for Traffic

EPOFLOOR LM is normally used as a line marking paint with EPOFLOOR range of products or car park deck coating systems.
Other applications include:
General epoxy and polyurethane coated decks
Car park flooring
Concrete and asphalt surface in factories, warehouses and car parks
Playground and sport flooring
Kerb stones and stair, treads
back to Industrial Flooring
Technical Information
Product Description

EPOFLOOR LM is a specially formulated fast drying line marking paint that can be applied in one coat for marking lines on concrete, asphalt, epoxy or polyurethane surfaces. EPOFLOOR LM paint is based on modified chlorinated rubber hybrid.

  • Single component easy to apply
  • Suitable for exterior and interior applications
  • Quick drying
  • Excellent resistance against water, oil, alkalis and hydrocarbon fuels
  • Good adhesion to concrete, asphalt, epoxy and polyurethane coatings
  • Durable with excellent abrasion resistance
  • Good reflection properties when mixed with glass beads
Packaging, Coverage / Consumption


The product supplied in 4 Liter and 15 Liter cans



Approximately 5-6m2/Liter for 100 micron, (dry) depending on the surface conditions and method of application.

Shelf Life & Storage


Keep the product in tightly closed containers stored in dry covered place, at a temperature not less that +5°C and not more than +35°C. Under these conditions, the product will have a shelf life of 12 months.

Yellow, white and black
Technical Properties
Appearance  Liquid
Color  Yellow, white and black
Mix density at 25°C  1.45 kg /L 
Solid content 65%
Touch dry at 25°C Approx. 10 minutes
Application temperature  5°C to 35°C 
Recommend minimum dry film thickness 100 microns
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface preparation

The surface should be sound, clean, dry and free from loose material, laitance, dirt, oil, grease or any other contaminants. If needed, wash the surface with detergent and then with clean water. Allow to dry completely before application. Do not use solvent to clean the surface before applying the product.


Mix the contents of the container thoroughly for 1 minute before application. Do not add any kind of solvents.


EPOFLOOR LM can be applied with brush, roller or airless spray gun. It may be needed to dilute the product with 5 to 10% SOLVENTE 10, if airless spray gun is used. The nozzle tip of the gun should be from 4-6mm. Apply the paint with a pressure of 30-40 psi.

Apply EPOFLOOR LM at a rate of 5m²/Liter (200 microns wet). If another coat is needed to build up the thickness, then apply the second coat of the applied coating while it is still wet.


Clean tools with SOLVENTE 10 promptly before material hardens. Cured material must be mechanically removed.


  • Do not apply the paint during rainy or stormy weather or when humidity is greater than 80%.
Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.


In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.


If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.29Mb)
More Products from this section
Monneli Epofloor LM UV

Two Components Line Marking Polyurethane Coating for Traffic

Monneli Elastojoint SB20

Hydrophilic Swellable Waterstop Joint Profile

Bases and concrete header walls
Foundation walls
Underground concrete structures
Concrete tanks and sewerage collectors
Pipe penetrations
Subway stations
Water treatment plants
Swimming pools
Tunnels and pits
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map