Industrial Flooring

Line Marking Coating

Monneli Epofloor LM UV

Two Components Line Marking Polyurethane Coating for Traffic

As a line marking paint with Epofloor range of products or car park deck coating systems.
General epoxy and polyurethane coated decks
Car park flooring
Concrete surface in factories, warehouses and car parks
Playground and sport flooring
Kerb stones and stair, treads
back to Industrial Flooring
Technical Information
Product Description

A specially formulated fast drying line marking paint that can be applied in one coat for marking lines on concrete, epoxy or polyurethane surfaces. EPOFLOOR LM UV paint is based on Polyurethane.

  • Suitable for exterior and interior applications
  • Quick drying
  • Excellent resistance against water, oil, alkalis and hydrocarbon fuels
  • Good adhesion to concrete, epoxy and polyurethane coatings
  • Durable with excellent abrasion resistance
  • Good reflection properties when mixed with glass beads
Packaging, Coverage / Consumption


Product Pack size Coverage
EPOFLOOR LM UV 4 Liter 5-6m² / Liter

Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage. In case of use of antislip aggregates, the consumption values for the top coat will be reduced by 15 - 20%.

Shelf Life & Storage


Original sealed kit of Epofloor LM UV has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35°C. Keep the product in tightly closed containers stored in dry covered place, at a temperature not less that +5°C and not more than +35°C. Under these conditions, the product will have a shelf life of 12 months.

5 Colors: 1023 3020 5017 6024 9016
Technical Properties
Appearance Liquid
Color  5 Colors:
Mix density at 25°C 1.45 kg /L
Solid content 65%
Touch dry at 25°C 3 hours
Application temperature 5°C to 35°C
Recommended minimum  dry film thickness 150 microns
All values are subject to 5-10 % tolerance 
Application Information
Instructions for use

Surface Preparation
The surface should be sound, clean, dry and free from loose material, laitance, dirt, oil, grease or any other contaminants. If needed, wash the surface with detergent and then with clean water. Allow to dry completely before application. Do not use solvent to clean the surface before applying the product.


Mix the contents of the container thoroughly for 1 minute before application. Do not add any kind of solvents.

Epofloor LM UV can be applied with brush, roller or airless spray gun. If airless spray gun is used. The nozzle tip of the gun should be from 4-6 mm. Apply the paint with a pressure of 30-40 psi.

Apply Epofloor LM UV at a rate of 5m2/Liter (200 microns wet). If another coat is needed to build up the thickness, then apply the second coat after the first one is totally dry.

For the light reflection, proper glass beads with size.

Clean tools with Solvente 10 promptly before material hardens. Cured material must be mechanically removed.


Do not apply the paint during rainy or stormy weather or when humidity is greater than 80%.

Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary. In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
More Products from this section
Monneli Epofloor LM

Line Marking Coating for Traffic

Monneli Epochim K100

High Chemical Resistant Epoxy Coating

EPOCHIM K100 is used as follows:
A resistant coating against chemicals. It also acts as an abrasion protective coating for floors and walls and aggressive products, stored in concrete tanks
As an abrasion and chemical resistant coating in seawater tanks, sewage works, manholes and pipe linings
Due to its smooth and easily cleaned surface, EPOCHIM K100 is especially suited for wet rooms of all types, abattoirs, dairies and agricultural buildings, etc.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map