Tile Grouts

Epoxy Based Tile Grouts

Monneli Neofil Poxy WB

Water Cleanable Epoxy Tile Grout

NEOFIL POXY WB can be used as follows:
Grouting of ceramic, porcelain, and quarry tile coverings, acid resistant floor brick, pavers and natural stone tiles
It is ideally suited for heavy duty commercial installations-indoor and outdoor, where materials are exposed to high trafficking, thermal shock and chemicals
For application in food processing plants, commercial kitchens, hospitals, fast food outlets, swimming pools, laboratories
back to Tile Grouts
Technical Information
Product Description

A user friendly, 100% solids, water cleanable epoxy grout used for permanent, chemical resistant grouting of ceramic, glass and stone tile. NEOFIL POXY WB is excellent for counter tops and areas with high traffic and physical abuse.


n Excellent adhesion to damp and dry surfaces

n Water proof, hygienic, hard wearing and impact resistant

n Good resistance to chemical attack

n Easy to apply

n Water cleanable

Compiliance Standard

n ANSI A 118.3

n EN 13888 as RG

n ISO 13007 as RG

Packaging, Coverage / Consumption


NEOFIL POXY WB is supplied in a 2 components 5kg, 8kg and 10kg kit.



Consumption is according to joints depth and width and the size of tiles. Accurate quantity of consumption can be calculated using following formula:


Formula:    A + B x W x D x 1.59 = Kg./m²
                    A x B

W = width of joint (mm)
D = thickness of tile (mm)
A = length of tile (mm)
B = width of tile (mm)

Shelf Life & Storage


Store in dry and covered place out of direct sunlight and protect from high temperature (higher than 35ºC).


Shelf life:

12 months if stored as recommended.

White, grey, black, other colors upon request
Technical Properties
Color White, grey, black, other colors upon request
Wet density at 25⁰C  1.59 kg/L 
VOC 9.0g/L 
Open time 60 minutes
Compressive strength 50 N/mm²
Flexural strength >25 N/mm²
Water absorption at 7 days 0.3%
Shrinkage (7 days) <0.25%
Sag (Vertical joints) None
Chemical resistance Excellent for most solvents, acids, alkalis
Load bearing strength After 24 hours
Service temperature -5⁰C to +80⁰C
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface preparation

The below surface, tiling mortar must have set sufficiently hard. Remove excess adhesive or mortar from the joint area so that 2/3 of the depth of the tile is left available for grouting.

Grout joints and tile surface should be swept or vacuum cleaned. It should be free of standing water, dust, dirt and foreign material.


The base and hardener components should be individually stirred to re-disperse any settlement. Transfer part B into the can of Part A and mix thoroughly using a slow speed electric drill with a paddle attachment, taking care to avoid air entrapment which cause pinholes in the grout. Scrape the sides and bottom of the can to assure complete mixing until a uniform consistency and color is obtained. Do not overmix as this will cause the epoxy to flash set.


Allow the tiles to set firmly before grouting (1 to 2 days). Pour the mixed grout onto area to be grouted. Spread grout into open joints of tile or brickwork starting at the lowest areas, making sure grout joints are completely full and then working to the highest areas.

Using a hard rubber float, work grout into the joint and strike excess grout from the tile faces in a squeegee fashion. Be certain to pass over joints on a 45º angle so as to not disturb the grout that has already flowed into joints. Remove all excess epoxy from the surface of the tile with the rubber float before it begins to set by turning the float perpendicular to the tile surface and skimming it diagonally off the tile surface.

Clean the remaining grout off the surface of the tile by making circular movements with a coarse sponge pad and a little water. Wipe off the resulting slurry with a soft sponge. Frequently rinse the sponge in clean water while cleaning the tile surface.

Do not begin cleaning the surface before NEOFIL POXY WB has started to set. For final cleaning, wait for at least 3 hours but no more than 6 hours to remove the remaining film from the surface with a soft sponge.


Tools, gloves and application equipment should be cleaned immediately with hot water, while material is still wet. Once the material gets hardened, mechanical removed will be necessary.

Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary. In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly. If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
More Products from this section
Monneli Neofil Poxy

High Performance Epoxy Grout for Tiles

Monneli Neofil PS

Polymeric Sand for Pavement Joints

Monneli Espansil


It is used to obtain non-shrinking and expansive mortars and concrete, where for the static reasons, the increase of volume is required. The principal fields of application are:
Reinforced plasters for the structural consolidation of brick
Reinforced concrete constructions
Grouting of channels and rocky embankment reinforced concrete ceilings, consolidation of vaults, etc.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map