Mortar Specialties

Cement Based Mortar

Monneli Rasante P-20S+

High Strength Cementitious Ready Dry Mix Plaster

RASANTE P-20S+ has an extensive use in both residential and commercial complexes in civil engineering and other areas of construction and interior designing due to its optimum compressive strength that could be acquired within a considerably short period of time.
RASANTE P-20S+ is recommended for plastering on block walls, ceilings, columns, bricks and concrete surfaces; it should not be used on painted surfaces.
back to Mortar Specialties
Technical Information
Product Description

A high strength cement based ready mix plaster. It is specially formulated for exterior and interior plastering work that gives an extra hard, smooth, and better shrinkage control base coat. Due to its exceptional content of additives and the use of precisely graded fillers, a homogeneous, superior adhesion, and a high workability product is obtained when mixed with water.
RASANTE P-20S+ is manufactured to provide a very good quality of plaster and can be applied manually by hand or by using spray machines.

  • High compressive and flexural strength
  • Very good impact strength
  • Easy to mix, apply and finish
  • Excellent adhesion to the substrate
Compiliance Standard
  • BS 5262, BS 5492
  • ASTM C 387, ASTM C109
Packaging, Coverage / Consumption


RASANTE P-20S+ is supplied in 50kg multi-layered bags.



Approximately 15-16 kg per m² for 10 mm thickness

Shelf Life & Storage


Store in dry covered place in the original closed bags. In these conditions, the product shelf life is 12 months from the date of production.


Technical Properties



Grey powder

Dry density at 25°C

1.70 kg/L



Grain size

0 – 2.5 mm

Pull out strength

> 0.5 N/mm²

Adhesion with DASHBOND SPX

>1.5 N / mm²

Compressive strength at 28 days (ASTM C 579)

Up to 25 N / mm²

Flexural strength at 28 days (ASTM C 580)

> 2.0 N / mm²

All values are subject to 5-10% tolerance

Application Information
Instructions for use

Surface preparation

The substrate should be free of loose particles, dust, dirt, grease, oil or paint. Absorbent and porous substrates should be moistened with water prior the application of RASANTE P-20S+.

In case of non absorbent surfaces, a spatter dash slurry coat DASHBOND or DASHBOND SPX (in case of AAC Block surface) should be applied as a key coat to improve adhesion and high bonding with the substrate.
In case of surface contains micro-silica, DASHBOND SPX spatter dash slurry should be applied to improve adhesion with the substrate.
Concrete or block substrates should have been allowed to cure sufficiently. All shrinkage movements should taken place before applying RASANTE P-20S+.
Do not apply RASANTE P-20S+ on surface exposed to movement, vibration or mechanical impacts.
Saturate the surface with water and wait for the evaporation of excess water before applying the mix.


RASANTE P-20S+ should be mixed with clean cold water to obtain a homogeneous mixture free from lumps. One 50 Kg. bag of RASANTE P-20S+ should be mixed with about 8 – 9 Liters of clean water. The mixture remains workable for 1 hour after mixing (at +25°C). Let the mix set for 5 minutes, then remix before application.


Apply RASANTE P-20S+ on the surface manually with a plastering trowel or by using a spraying machine in a single layer (up to 20mm).  When the plaster has “set”, smooth finishing can be achieved with a wooden or foam float. The Float should be moistened during the smoothing operation.
If more thickness is required, the application should be done in two layers. In the first layer, apply RASANTE P-20S+ in a thickness of 10-15mm, a rough texture is to be obtained to provide mechanical Key for the second layer. The second layer should b applied at least 48 hours after the first layer. Within this period cure the plaster with clean water. Apply the second layer at a thickness of up to 20mm.

If applying with spray machine, RASANTE P-20S+ mix should not be allowed to stand unused in the machine for longer than 30 minutes.
In order to ensure proper curing, it is advisable to keep the plastered surface moist and protected from sun and wind during the first 48 hours.


Tools and equipment shobeuld cleaned with water immediately after use. Hardened materials should be mechanically removed.


  • No further water should be added to the mix. Hard and set plaster should not be re-mixed or used.
  • Do not apply RASANTE P-20S+ onto gypsum, metallic and wooden supports.
  • During summer season, working area should be covered to prevent the direct sun effects. Keep equipment cool and use a cold water.
  • The applied plaster has to be water cured for a period of 3 days.
  • Before applying any kind of stucco finish, paint, or wall paper the plaster has to be allowed to dry out completely.
  • Should not be applied on floors or on painted surfaces.
Additional Information
Health & Safety

RASANTE P-20S+ is a cement based product. Avoid contact with eyes or skin.  
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
More Products from this section
Monneli Dashbond

Spatter Dash Bond Coating

Monneli Dashbond SP

High Quality Spatter Dash Bond Coating

Monneli Dashbond SPX

Superior Quality Spatter Dash Bond Coating

Monneli Dashbond STR

Superior Quality Spatter Dash Bond Coating

view more
Monneli Dashbond SPX

Superior Quality Spatter Dash Bond Coating

DASHBOND SPX is specially formulated for application on fair face concrete containing micro-silica and on AAC (Autoclaved Aerated Concrete) blocks, without a need to hack the surface.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map