Solvent Based Styrene-Acrylate Protective and Decorative Coating
MANTOCOLOR S is a solvent based single component acrylate based anticarbonation coating. It is used to provide outstanding protective and decorative coating for concrete and cementitious surfaces. MANTOCOLOR S is an economical and ideal system to protect exposed reinforced concrete from the atmospheric aggressive factors such as acid rains, chloride and sulphate ions, water etc.
Packaging:
MANTOCOLOR S is supplied in 20 liter in pails.
Consumption:
3.6 m2/Liters /coat
Storage:
Store MANTOCOLOR S in a dry and covered place away from direct sunlight into the original well-closed packaging. A shelf life of 12 months is expected if stored as recommended.
|
Surface preparation
The surface should be sound, dry, clean and free from grease, loose particles, oil, curing compound, laitance, or any other contaminating material.
Proper preparation for the suface is quite essential in order to achieve a good bonding with the coating. Grit blasting can be the best tool to achieve a clean surface. In case of algae or any other growth contamination, clean the surface with biocide after completing the grit blasting process.
After grit blasting, all surfaces should be cleaned of all loose material by blowing off the surface with dry oil free compressed air.
Remove all traces of curing compound and shuttering oil. Do not use paint remover or solvent to clean the surface. In case of deep contamination which is shown after blasting, clean the surface with steam using suitable detergent solution (in as 2% concentrate of non-ionic detergent in water).
In case of applying MANTOCOLOR S over an existing old coating, a trial to ensure its compatibility and bonding strength between both coating is required.
ACRYFIL, an acrylic based pinhole filler can be used for filling small pin holes and for levelling minor irregularities in order to achieve a uniform surface. If the surface contains medium size blow holes, minor irregularities or cracks, fill these holes using a suitable cementitious flexible plaster like RASOCELL.
Protect undesired areas which should not be coated, such as glass, plants, grass, asphalt painted areas, etc.
Priming
On the clean dry surface apply IDROSIL XS as a primer using brush or proper spraying machine with a rate of 2.5 m2/ Liter. Primer can be applied in one or two coats depending on the substrate surface.
Allow the primed surface to totally dry before applying MANTOCOLOR S. It is recommend to apply the coating material immediately after the primer is dry to avoid any future contamination to the primed areas.
Mixing
Stir MANTOCOLOR S in the container before use.
Application
Apply MANTOCOLOR S using suitable brush, roller or airless spray gun. It may be needed to dilute the product with 3-5 % by weight of SOLVENTE 10 if airless spray gun is used.
It is recommended to apply two coat of MANTOCOLOR S. The second coat should be applied after 24 hours of applying the first coat and should be applied at right eangles to the first coat. Each coat should be applied at a rate of 3.6 m2/ Liter.
The total recommended dry thickness for the system should not be less than 150 microns.
Curing
Allow the final coat to cure for 7 days to achieve its final properties.
Cleaning
Tools and equipment should be cleaned immediately after use with SOLVENTE 10. Hardened material should be removed mechanically.
Recommendations
MANTOCOLOR S is a solvent-based product. Avoid contact with skin or eyes. Provide adequate ventilation in working place to avoid inhalation of dust.Use suitable clothes, goggles and gloves while applying.
In case contact with eyes, wash abundantly with warm water and seek immediately for medical treatment.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Ready-mixed, Acrylic Pinhole Filler
Elastomeric, Protective, Anti-Carbonation & Waterproof Coating
Synthetic Latex Additive for Tile Adhesive