Adhesive & Grout for Glass, Ceramic Marble Mosaics
NEOFIL F10 is a high performance white colored cementitious adhesive. It is slip resistant and has good open time. NEOFIL F10 does not contain fiber, asbestos & other harmful components.
Packaging:
Neofil F10 is packed in 25 Kg bags.
Consumption:
Approx. 2.5 to 4.5 kg NEOFIL 10 per m² using notched trowel on smooth surface. Consumption will vary according to type of tiles and support condition.
Storage:
Store in dry covered place in the original closed bags
Shelf life:
12 month if stored as recommended.
|
Surface preparation
All surfaces should be sound, clean & uncontaminated. This preparation should leave an exposed concrete surface free from dust, loose particles, deleterious matter, oil, grease, chemical films & other contaminants.
All loose particles of mortar, paint, etc. must be physically removed.
Concrete or blockwork: allowed to cure sufficiently so that all shrinkage movements take place before fixing tiles.
Gypsum supports: treat with PRIMER A16. Should not have a percentage of humidity more than 10%.
The surface of substrates must be moistened slightly with clean water to reduce the absorption of water from the mortar. Do not moistened the tiles.
Mixing
Place 5.0 – 5.25 liters of cold, potable water (or ELASTOKOL as needed) in the mixing bucket and add slowly 25 kg bag of NEOFIL F10 under continuous mixing till a uniform lump free consistency mix is achieved. For mixing process, a slow speed drill (200- 300rpm) fitted with a suitable paddle is recommended.
Allow the obtained mix to stand for 5 minutes and then remix before application.
Application
Spread NEOFIL F10 on the substrate to a uniform thickness of 3mm using a toothed spatula, the first pass with its smooth part and the second pass, immediately after, to the desired thickness using the toothed part.
Place the tiles onto the adhesive bed. Apply sufficient pressure on the tile during fixing with slight twisting movement in order to ensure good contact with the mortar.
In case of large size tiles, it is necessary to spread the adhesive also to the backside of the tile and then place the tiles into the adhesive bed.
Apply enough material that can be tiled during the adhesive's open wet time. Spreading large areas may result in drying the adhesive before tiles can be fixed causing poor adhesion.
The mosaic and tiles should be installed starting from top towards the bottom with a firm pressure to ensure a good contact with the adhesive.
Finishing
Remove excess adhesive with damp cloth before the material has set. Joint grouting between tiles may be commenced 10hours after tiles has been laid on the walls and 24 hours after tiles are laid on the floors.
Cleaning
Tools and equipment should be cleaned with water immediately after use. Hardened materials should be mechanically removed.
Recommendations
NEOFIL F10 can be harmful to skin as it contains cement powders which may releases alkalis when mixed with water.
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.
In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of with eyes, rinse with plenty of water and seek medical advice accordingly.
If ingested, seek obtain medical attention immediately. Do not induce vomiting.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Two Component Fast - Setting Cementitious Tile Adhesive
Cementitious Adhesive for Natural & Artificial Stone
Synthetic Latex Additive for Tile Adhesive
Polymer Modified Floor Tile Adhesive Up To 15 mm Thick Mortar
THICK BED TILE ADHESIVE FOR INTERIOR & EXTERIOR USE
Acrylic based concrete curing compound
Synthetic Latex Additive for Tile Adhesive