High Performance Epoxy Mortar
EPOMORT HS is a three components solvent free epoxy based resin with a modified hardener and carefully selected and graded crush resistant aggregates to produce very strong, high quality nonshrink mortar. EPOMORT HS is especially suitable as a repairing mortar, for floor tapping when higher resistance to chemical attack is required.
Packaging:
EPOMORT HS is supplied in three components kit. It is available in 8kg and 16kg packaging.
Consumption:
One kit of EPOMORT HS will cover 1 m² at 4 mm thickness, depending on surface condition.
Storage:
Store in dry and covered place out of direct sunlight and protect from high temperature (higher than 30°C). If stored as recommended its shelf life would be 12 months from the manufacturing date.
|
Concrete Preparation
Surface must be clean and sound. Remove all dirt, laitance, grease, curing compounds or any other foreign matter. Sandblasting or mechanical abrasion should be used to remove harsh corrosion or extreme contamination.
The decayed or damaged area to be repaired should be marked with a marker. Cut the marked area to a depth of at least 5mm using a hand held concrete saw or disc grinder to avoid feather edging and to provide a square edge. Break out or chip the complete repair area down to sound base using sharp tools or chipping hammer.
Steel Preparation
All corroded steel should be completely cleaned. It is recommended that grit blasting be used to clean the reinforcing steel. Particular attention should be paid to the rear side of the bar to ensure all corrosion products have been removed.
Priming
Concrete Priming
The product is self-priming; however, if the substrate is highly porous, PRIMER POXY FF a solvent free high performance epoxy primer shall be used.
Steel Priming
The cleaned steel should be coated within 3 hours.
Apply one coat of BETOFER, a corrosion proof cementitious based primer or EPOZINC, a two component Zinc rich EPOXY PRIMER, continuously with brush onto the cleaned bar reinforcement ensuring that the whole steel surface area is completely covered. Allow to dry before proceeding with the repair.
Mixing
EPOMORT HS is supplied as a three component kit consisting of base component, curing agent and a bag of selected, graded aggregate. The resin and hardener components should be stirred separately for three minutes or until thoroughly blended. The contents of the hardener should be added to the resin component and stirred with a force action mixer or a heavy duty, slow speed drill fitted with a mixing paddle until all the components are thoroughly blended. Then slowly add the entire amount of aggregates to the resin while the mixer is still running. Partial mixing of the three components should not be applied under any circumstances.
Application
It is recommended to apply EPOMORT HS horizontally in layers of 50 mm maximum and 5 mm minimum. In vertical applications, EPOMORT HS can be applied up to 12 mm thick in single layer without the use of formwork. For large thicknesses, apply EPOMORT HS in subsequent layers within 8 to 12 hours. If this time is exceeded, the surface should be re-primed prior to proceeding with the successor layer.
Apply the mixed product firmly onto the tacky primer using a trowel. Apply the product in layers to build up the required thickness. Use a wooden float to compact the applied layer to ensure a complete secured bonding of the applied product to the surface. Before setting, use a steel trowel to smoothly finish the mortar surface.
Cleaning
Tools and equipment should be cleaned with SOLVENTE 10 from Colmef immediately after use.
Hardened material should be removed mechanically. Spillages should be absorbed with sand or sawdust and disposed of in accordance with local regulations.
Recommendations
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.
In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.
If ingested, obtain medical attention immediately. Do not induce vomiting.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Fairing Coat Solvent Free Epoxy Mortar
Fairing Coat Solvent Free Epoxy Mortar (3mm or less)
Epoxy Thixotropic Adhesive for Structural Gluing
General Purpose Epoxy Mortar
High Build Solvent Free Epoxy Flooring System
Solvent Free High Performance Epoxy Primer
Thinner / Cleaning Solvent