Highly Deformable Cementitious Tile Adhesive
NEOFIL F50 S1 is a cement based professional grade highly deformable tile adhesive that works with most types of tiles and flexible substrate.
NEOFIL F50 S1 is composed of a blend of cement, carefully selected aggregates, special additives, and polymers. The product is suitable for internal as well as external use. It does not contain asbestos nor any other harmful components.
NEOFIL F50 S1 is used for internal and external tile laying both on wall and floor applications. It is suitable for use on the following:
Packaging:
NEOFIL F50 S1 is packed in 25Kg bags.
Consumption:
Approximately 4.0 to 4.5m² at 3mm thickness application per 25 kg bag of NEOFIL F50 S1. Consumption will vary according to type of tiles and support condition.
Storage:
Store in dry covered place below 35°C in the original closed bags and shelf life is 12 months if stored as recommended.
|
|||||||||||||||||||||||||||||
Surface Preparation
Apply the mixed mortar adhesive in a thin layer, and firmly press onto the surface that will be tiled and work with the trowel’s flat edge. Comb the adhesive with a suitable notched trowel horizontally to achieve a 3-8 mm bed thickness. Spread the mortar adhesive to a manageable area that can be tiled within 5-10 minutes. Press the tiles firmly over the mortar adhesive and immediately knock them into the desired position. Adjust the position of the tiles, if required within its adjustibility time of 5-7 minutes after installation.
Mixing
Place 7-7.5 Liters of cold, potable water in the mixing bucket and add slowly 25kg bag of NEOFIL F50 S1 under continuous mixing for 3-4 minutes till a uniform lump free consistency mix is achieved. For mixing process, a slow speed drill (200-300rpm) fitted with a suitable paddle is recommended. Allow the mixed material to stand for about 10 minutes and remix briefly without adding further water.
Application
Apply the mixed mortar adhesive in a thin layer, and firmly press onto the surface that will be tiled and work with the trowel’s flat edge. Comb the adhesive with a suitable notched trowel horizontally to achieve a 2-6 mm bed thickness. Spread the mortar adhesive to a manageable area that can be tiled within 5-10 minutes. Press the tiles firmly over the mortar adhesive and immediately knock them into the desired position. Adjust the position of the tiles, if required within its adjustibility time of 10 minutes after installation.
In case of large size tiles, it is necessary to spread the adhesive also to the backside of the tile and then place the tile into the adhesive bed.
Apply enough material that can be tiled during the adhesive’s open wet time. Spreading large areas may result in drying the adhesive before tiles can be fixed causing poor adhesion.
Allow the installed tiles to remain undisturbed for at least 24 hours.
Mortar adhesive must not rise between tile joints higher than halfway the thickness of the tiles. It is recommended to use Neofil Color to fill the joint gaps after 2 days of installation.
Cleaning
Tools and equipment should be cleaned with water immediately after use. Hardened materials should be mechanically removed.
Recommendations
NEOFIL F50 S1 can be harmful to skin as it contains cement powders which may releases alkalis when mixed with water.
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.
In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.
If ingested, obtain medical attention immediately. Do not induce vomiting.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Two Component Fast - Setting Cementitious Tile Adhesive
Cementitious Adhesive for Natural & Artificial Stone
Synthetic Latex Additive for Tile Adhesive
Polymer Modified Floor Tile Adhesive Up To 15 mm Thick Mortar
THICK BED TILE ADHESIVE FOR INTERIOR & EXTERIOR USE
Latex Modified Cementitious Tile Grout for Joints 4-20 mm Wide
Synthetic Latex Additive for Tile Adhesive