Self Leveling Polyurethane Floor Topping
A solvent free, high performance three component pigmented self-leveling floor topping which provides a surface with excellent resistance to abrasion, chemical attack and other forms of physical aggression.
EPOFLOOR SLP50 is designed as self leveling polyurethane for use in concrete floors or steel substrates with thickness from 2.5 mm to 5 mm.
EPOFLOOR SLP50 has high filling ability when applied to concrete floors. Once cure, it provides a watertight seamless coating with uniform colour.
Packaging:
EPOFLOOR SLP50 is supplied in 15 Liter Kit.
Consumption:
1 m²/Liter for 1 mm thickness depending on substrate condition
Storage:
Keep the product in dry and sheltered place at temperature between 0ºC and +35ºC.
Shelf life:
At least 12 months if stored as recommended.
|
Surface preparation
Support must be dry, compact, free of dust and other contaminating substances like oil, grease, etc. The humidity should not be greater than 75% at the time of application, and the moisture content of the substrate shall not be more than 5%.
The pull-out resistance trial on the concrete screed must give a result non-inferior to 20 N / mm². The right surface preparation will help to achieve the required adhesion strength between the substrate and the coating.
It is recommending to sand blast the substrate in order to guarantee a clean surface and to create a mechanical key between the substrate and the coating. Repair all the existing expansion joints using EPOMORT HS and be sure to follow the same joints through the new floor. Cracks should be treated using EPOFINISH. Use ARMOFLEX, a fiber glass mesh for moving cracks.
Priming
All surfaces must be treated with PRIMER PU, a solvent based epoxy primer.
The primer should be applied by brush or roller on to the cleaned surface area (particularly hidden surfaces) at a rate of 6-8 m²/Liter. The primer should be left to achieve a tack-free condition for 8-12 hours before applying the floor coating. A second coat of primer may be required if the substrate is excessively porous.
Mixing
EPOFLOOR SLP50 must be mixed at the moment of use. The base (Component A) should be mixed for two minutes with a drill at low number of turns (200-300 RPM) till obtaining a homogenous mix. Pour the hardener (Component B) into the base mixture and mix for another two minutes. Add the filler (Component C) and mix until uniform consistency is achieved. Scrape the sides and bottom of the container during mixing to ensure homogeneity.
Application
Pour the mixed material onto the primed surface in pools or as a long strip. Using a trowel, pin screed, or notched trowel, spread EPOFLOOR SLP50 to the required thickness. To release entrapped air and assist with the smoothing operation, roll the material within 5 minutes after it is levelled, using spiked roller.
Allow to cure for minimum 18 hours at 25°C for light traffic.
Cleaning
Tools and equipment should be cleaned with SOLVENTE 10 from Colmef immediately after use. Hardened material should be removed mechanically. Spillages should be absorbed with sand or sawdust and disposed of in accordance with local regulations.
Recommendations
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary. In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly. If ingested, obtain medical attention immediately. Do not induce vomiting.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Seamless, Flexible, Polyurethane Flooring System
Seamless, Polyurethane Traffic Deck Coating System
Protective, Polyurethane Based Traffic Deck Coating System
Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System
Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System
Tile Adhesive on Gypsum Board Substrate
Polyurethane Primer
Thinner / Cleaning Solvent