Tile Grouts

Cement Based Tile Grouts

Monneli Vetromix

Grout for Sealing Glass Blocks

Uses
VETROMIX is used for fixing and grouting of glass blocks within cement block or concrete openings. It is suitable for internal and external use.
back to Tile Grouts
Technical Information
Product Description

A special powder mortar composed of hydraulic binders, fillers and synthetic resins. When mixed with water, it becomes easily workable and adheres perfectly to the support, as well as, between the glass block. After curing it becomes water proof and flexible grout. VETROMIX is also suitable for grouting tiles joints. VETROMIX does not contain asbestos fibers or other materials that can be harmful for the health of the applicator.

Advantages
  • Can be used as adhesive, as well as, grout for glass block
  • Flexible, non yellowing and waterproof grout
  • Single part and easy to apply. It requires only addition of water
  • High mechanical properties.
  • Excellent adhesion between glass block, as well as, to substrate
  • Impermeable with resistance to staining
Packaging, Coverage / Consumption

Packaging:

VETROMIX is supplied in 20 Kg bags.

 

Consumption:

10 to 12 Kg / m² for glass block of 150 x 150 x 80 mm and joint width of 20 mm.

Shelf Life & Storage

Storage:

Keep the product in dry and covered place. In these conditions the product will have a shelf life of 9 months.

Technical Properties
PROPERTIES

RESULTS

Color

White

Appearance

Powder

Density

1.9 kg/L

pH of mixture

12.8

Workable time at 25⁰C

60 minutes

Compressive strength after 28 days

20.0 N / mm²

Flexure strength after 28 days

8.0 N / mm²

Temperature of application

+5⁰C to +35⁰C

Joints thickness

from 2 to 25 mm

Noxiousity ECM 88/379

No

All values are subject to 5-10 % tolerance

Application Information
Instructions for use

Surface preparation

Horizontal supports must be leveled and vertical side should be perfectly in plumb in order to guarantee a perfect alignment of the glass blocks. The support must be solid, compact, and free from inconsistent parts, dust and grease substances.

Mixing

Pour into a container about 6 - 6.5 Liters of clean water then add a 25 Kg bag of VETROMIX. Mix till a homogeneous lump free consistency is obtained. Let the mixture rest for about 5 minutes, and remix it shortly before use.

Application

Apply VETROMIX with a trowel, then position the glass blocks in the opening. Use special moulder to verify the glass block alignment. Remove the excess of mortar before it hardens. For large openings it is strongly advisable to increase the mechanical strength and improve the structure stability of the glass block. It is recommended to fix, in every line of blocks or every other line, an iron rod of 6 mm dia. As soon as the structure is stable sufficiently, it is possible to begin the phase of grouting the blocks and then remove the moulders.

Apply VETROMIX into clean joints, free from dust and any form of hardened residues. Compress the product using a smooth rubber grout float. Let the product harden for about 10 minutes, after that clean the surface using a damp sponge. When the product is well hardened, clean the surface with a dry rag.

If the surface exceeds 15 - 16 m² area, a proposed expansion joints must be implemented. Concrete expansion joints should be sealed with elastic material as ELASTOSEAL PU.

Cleaning

Tools and equipment should be cleaned with water immediately after use.

Recommendations

  • VETROMIX is a cement based product and it must be cured as common norm of practice. If applied externally, it must be protected from rain, excess warm and direct sun-rays till it hardens completely
  • For large area of glass block openings, 6 mm steel reinforcement rod or mesh reinforcement might be needed within the grout. Contact Colmef Technical Department or consult structural Engineer for the proper requirements
Additional Information
Health & Safety

VETROMIX can be harmful to skin as it contains cement powders which may releases alkalis when mixed with water.

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Fugacolor

Water Repellant Anti-Fungus Tile Grout

Monneli Giuntolastic

Synthetic Latex Additive for Cementitious Grout

Monneli Neofil Color 0-4 mm

Latex Modified Cementitious Tile Grout for Joints 0-4 mm Wide

Monneli Neofil Color 4-20 mm

Latex Modified Cementitious Tile Grout for Joints 4-20 mm Wide

Monneli Neofil Grout Thick

Latex Modified Cementitious Tile Grout for Joints 4-20 mm Wide

view more
RANDOM PRODUCT
Monneli Epofloor E240

SOLVENT FREE PERFORMANCE, HIGH BUILD EPOXY FLOORING  SYSTEM

Uses
EPOFLOOR E240 is used for a variety of industrial applications such as:
Production assembly areas, workshops, dairies, bottling plants, breweries, pharma plants, kitchens, showrooms, etc.
Anti-slip floors, ramps & high traffic
Wet working areas
Floor coating for car-parking
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map