Seamless, Polyurethane Traffic Deck Coating System
EPOFLOOR P1140 is a multi-layered, seamless, UV stable, polyurethane deck coating system. It is designed for floors where superior impact and wear resistance are required.
PACKAGING | ||
PRIMER PU | 15 liter kits | |
EPOFLOOR P380 | 15 liter kits | |
EPOFLOOR P500 | 15 liter kits | |
QUARTZO No. 2 | 25 kg bags | |
SOLVENTE 10 | 20 liter pail | |
EPOFLOOR LM | 15 liter |
CONSUMPTION | ||
PRIMER PU | 6-8 m²/Liter depending on surface texture and porosity | |
EPOFLOOR P380 | from 4.0m²/Liter at 200 microns DFT | |
EPOFLOOR P500 | 3.0 m² / Liter coat (anti-slip) 4.0 m² / Liter/coat (smooth) at 200 microns DFT |
|
EPOFLOOR LM | 0.6-2.0 kg/m² depending on application |
Storage:
Store EPOFLOOR P1140 in dry and covered shed. Exposure to extreme temperature and direct sun light results in the deterioration of the product’s efficiency and reduces its shelf life. If stored as recommended its shelf life would be 12 months from the manufacturing date.
|
EPOFLOOR P1140 SYSTEM COMPONENTS | |||
PRIMER PU | Solvent based epoxy primer | ||
EPOFLOOR P380 | Single component polyurethane protective traffic coating | ||
QUARTZO No. 2 | Graded aggregate (0.3 - 0.9 mm) | ||
EPOFLOOR P500 | Single component polyurethane UV resistant traffic coating | ||
EPOFLOOR LM | Line marking coating |
Surface preparation
The surface should be sound, clean, dry and free from loose and flaking materials, efflorescence, laitance, curing compounds, dirt, oil, grease or other contaminants. Mechanical methods like grinding or grit/captive blasting in order to provide a suitable profiled open textured surface is strongly recommended.
New concrete or cementitious surfaces should be at least 28 days old and have moisture content not exceeding 5%. Old or existing floor should be refurbished mechanically to ensure clear sound substrate.
Surface irregularities and blow holes shall be repaired with EPOFINISH.
Expansion joints shall be repaired using EPOMORT HS, a high strength solvent free epoxy mortar.
After all preparation is complete, ensure dust is removed from the surface using an industrial vacuum.
Application
Priming
Apply single component PRIMER PU using a suitable roller at the rate of 5-6m²/Liter depending on the substrate profile and porosity.
The primer should be left to achieve a tack-free condition for 6-8 hours before applying the top coat. If the substrate is excessively porous, a second coat of primer shall be applied again.
For Anti Slip Surface
Broadcast QUARTZO No. 2 at a rate of 0.4 to 1.0 kg/m2 while the primer is still wet. Allow the applied product to cure for 16 hours. Remove the excess sand. Remove loose or prominent particle using a trowel then clean the substrate with a vacuum.
Intermediate Coat
Stir properly EPOFLOOR P380 to ensure uniformity of color before application. Product will be ready for use. Apply by roller or airless spray to the primed tack-free surface at a minimum consumption rate of 4.0 m2/ Liter per coat.
For ramps and turning areas, apply an additional coat of EPOFLOOR P380 at the same rate.
Top Coat
Stir EPOFLOOR P500 properly to ensure uniformity of color before application.
To provide a UV resistant coating to the system and to enhance durability performance, apply one coat of EPOFLOOR P500 at a minimum rate of 4.0 m2/Liters for pedestrian traffic and 3.0m2/Liters for vehicular traffic by roller or airless spray.
Line Marking Coating
Mix the content of the container before application. EPOFLOOR LM can be applied by brush, roller, and airless spray at the rate of 5m2/Liters for 200 micron DFT (Dry Film Thickness).
Recommendations
Avoid contact with skin & eyes. Protective clothing such as gloves & safety goggles should be worn during application. Treat any splashes to the skin or eyes with fresh water immediately. Should the product be accidentally swallowed, do not induce vomiting, but call for medical assistance immediately. Ensure adequate ventilation at site and avoid inhalation of vapors.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Seamless, Flexible, Polyurethane Flooring System
Protective, Polyurethane Based Traffic Deck Coating System
Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System
Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System
POLYURETHANE COATING FOR CONCRETE FLOORS
HYBRID POLYUREA
Fairing Coat Solvent Free Epoxy Mortar
Line Marking Coating for Traffic
Single Component Polyurethane UV Resistant Traffic Coating Low...